aluminum tube connector 3d models

The Aluminum Tube Sofa is a masterpiece crafted by Todd Merrill Custom Originals. Dimensions are as follows: Length measures 261.6 cm, Height reaches an impressive 801 cm, Depth stands at 109.2 cm, and Seat height sits comfortably at 431 cm. The...

I picked up some straight 1/2" aluminum square fence tubing for $1/lb at the local scrap yard and cut them to the desired lengths. I'll update this post later with pics once I enclose the lid, add a front door, and wire it up with an exhaust fan and...

Tube type is optional, I used a common polycarbonate straw like they use in large portable drinking bottles (I picked up 5 at the WM for like $2 so have spares) and I like this config as it lets you see the powder as it drops with no static so far...

Over the summer, we had to re-roof the house, I decided it was time to run ENT NON METALIC CONDUIT Tubing or sometimes called "smurf tube" for cameras and sensors along the soffit.when I ordered the tubing from a BIGBOX STORE they were all out of the...

Customized Version of Thingiverse Design: http://www.thingiverse.com/thing:1324986 Created with Customizer Tool: http://www.thingiverse.com/apps/customizer/run?thing_id=1324986 Instructions for Building: Using the Following Options: Join Type:...

Used to hold the PTFE tube that passes trough in filament storage box but can be used wherever one needs a PTFE tube.I couldn't get the original threading to work so I made a smaller version without need for screws. The parts are threaded so to fit...

Updates are live in the OpenSCAD file, simplifying configurations by adjusting tube size and wall thickness for varied corners. ... Slic3r support settings include: Pattern: rectilinear Pattern Spacing: 2.5mm Pattern Angle: 0 degrees Interface Layers:...

I designed these modular shelves from scratch using 8 mm aluminum round tubes as the structure. These tubes are extremely affordable and widely available, costing approximately 1.5 € per meter. You'll likely only need two meters unless you're...

... ...I also upgraded my Bowden tube to a high-quality Capricorn model and installed the matching Capricorn fittings, making sure everything was securely in place. However, this left me with a problem - my cover and filament guide no longer fit properly.

Generic sci-fi tube connector, for use in general props and cosplay, originally for use at Orion Sphere LRP (http://www.orionspherelrp.co.uk). It's octagonal in shape, and has some detailing with the correct directions to lock and unlock it. Uses a...

This is a small bracket that holds a Bowden tube connector to guide filament to a direct drive extruder. This installs with the holes the extruder motor used to be located.</p><p>Uses M3 screws and two nuts to attach to the extruder motor bracket.

This is a remake of the [Toothpaste Tube Squeezer](https://www.thingiverse.com/thing:2213704) by [@somethingtohide](https://www.thingiverse.com/somethingtohide), which itself is a remake of [this one](https://www.thingiverse.com/thing:1147252) by...

Originally designed to cradle PTFE tubes passing through filament storage boxes, this versatile holder can be repurposed anywhere a PTFE tube is needed. I encountered an issue with the original threading, so I created a smaller version that...

Used to hold the PTFE tube that passes trough in filament storage box but can be used wherever one needs a PTFE tube.I couldn't get the original threading to work so I made a smaller version without need for screws. The parts are threaded so to fit...

Humans link up two water tubes made of 3/8 inch tubing.

\r\n* My **aluminum tube** is 30cm long which gives it a tough fit.\r\n* I am using standard **16mmx3mm SPAX** for the feeders. You can use the one with or without an hexnut hole. One for the bigger teflon tube holders is attached as well.\r\n\r\n> I...

... to solve the issue when Teflontube comes loose from its connection. ...The top connector is identical to the one used on my hotend, which is PC4-M10, while the other original connector matches the Anycubic Mega I3's specifications, being a PC4-M6.

This thing connects either two 32mm inner diameter (measured 31mm) tubes with each other or, as I used it, connects a flexible tube to a rainwater barrel using a rubber seal (see pictures). This way I solved the inlet of my rainwater barrel. Similar...

Needed to replace the connector which broke off my Dyson.Have printed horizontally and vertically, not sure which is stronger for this yet.

I added a hole for the bowden tube so you don't have to drill it. ...Works with Sunlu S2 dryer.

This is a Simple Adapter to bridge the gap between the Filament runout sensor and the white bowden tube of the extruder. ... Makes guiding filament throught way easier.

The predecessor exhibited woefully inadequate thread alignment, consistently escaping the confines of its tubing receptacle; consequently, I engineered a replacement component to address these issues.

This adapter is ment to connect two 36mm inner diameter flexible PVC tube to each other. I printed this with a Prusa MK3s in quality mode and the tube is easy to screw in and has a nice tight seal. ... Hope you find it useful for your own purpose :) ...

... 16 mm carbon fiber tubing in mind. ... The design utilizes 16 mm inner diameter and 21 mm outer diameter tubing, resulting in an ID/OD length of 30 mm. ... One quarter inch twenty tappable holes are strategically placed to provide additional support.

... ...To further clarify, this connection will allow the fan to blow air into the tube, potentially increasing airflow within your system. ...If you need any more information or would like to discuss other ways to optimize your setup, feel free to ask!

The elbow connector is specifically designed to fit VW 12mm vacuum lines, as well as various other components. ...In my setup, it's being used to link the crankcase vent line directly to the carburetor intake.

http://www.thingiverse.com/apps/customizer/run?thing_id=1324986 Instructions Using the following options: Connector Type: Round Inline Connector Number of Small Sizes: 0 Number of Medium Sizes: 2 Wall Thickness for Small Size: 1 mm Wall Thickness for...

Added `holder.scad` that generates a support for the test tubes and depends on `portal_flat.scad` # Parameters: - `nb_holes`: number of ports desired - `depth`: depth of the portal, including corridor/foraging area # Modifications from original...

Corner bracket I designed for a camera apparatus. ...Used with 16 mm carbon fiber tubing. ...ID = 16.1 mm OD = 21 mm ID/OD length = 30 mm corner holes = 1/4"-20 tappable Category: Robotics

A quick clamp to keep the PTFE tube stationary as the filament moves with the push fitting during extruder retraction when working with PETG. ...It's uncertain if this would work effectively with PLA due to its brittleness.