aluminum square tubing fittings 3d models

The coffee cup I was using for holding little misc tools was getting top-heavy and tippy, so I designed this base to be used with aluminum square tubing. The tubing was cut to 3", 4" and 5" lengths, then friction-fit onto the base (I had to clean...

These fittings are designed to slide over the LED strip and fit into the end of 3/8" tubing. That tubing can then be affixed twisted moulded and handled roughly without compromising the LED strip. ... NOTE: These fittings are designed to work with...

Aluminum square tube tripod model saved in .step AP214 format.3 types of tripods are loaded - folded, partially installed and fully installed.The tripod is designed for the manufacture of aluminum pipes of round, square and rectangular cross-section....

I recently acquired a collapsible trade-show display wall consisting of numerous 0.5" square aluminum extrusions with 0.04" thick walls, along with a variety of plastic components, rivets, and webbing straps. This massive structure expands to...

While building robots for First Robotics Competition (FRC), we frequently rely on a lot of 1" and 1"x2" aluminum tubing, drilling numerous holes in the process. Measuring and marking multiple 1/4" holes at precisely 1/2" on center, right along the...

It will use 1 inch extruded aluminum square tube easily sourced at local hardware stores, and basic electrical components. It uses Daylight curable resin with no modifications needed to the display. ...I have 15 of these monitors laying around and this...

It will run on basic electrical components and easily sourced 1-inch extruded aluminum square tube from local hardware stores. The printer uses Daylight curable resin with no modifications needed to the display - a major advantage. ...I have 15 of these...

An aluminum alloy slip-fit bus support is designed for use with aluminum tubing. ...Its adjustable base slots allow for up to a 60-degree rotation, ensuring precise alignment.

This RC aircraft features a durable aluminum frame with 3/4 inch square tubing and ABS support pieces. The Multiwii platform is utilized, as demonstrated in videos (http://www.youtube.com/watch?v=7DHoLYf5pMA). For assembly, follow the instructions...

The .STL file contains precise dimensions for standard 1/2 inch square tubing, but you may need to adjust the inside dimension slightly (in the Customizer or in OpenSCAD) to ensure a smooth fit.\r\n\r\nI employed a very similar design concept to...

A hanger to support hanging plants (or anything) from the side of square tubing. I printed with supports.

I wanted to use some existing tubing I had laying around to make an enclosure for my BIBU B1 SE PLUS. ...These work really well on the 9.5mm square tubing.

... new version was designed for improved printability and created in Fusion360 instead of OpenSCAD. The provided .stl file should work for 1/2-inch (12.7mm) square tubing. I printed eight of these to join the square tubing for a printer enclosure.

This is my design for a hinge that can be used on any multicopter with a 14mm square tubing arm, easily scaled to fit different tubing diameters. It's likely to have other uses as well. I haven't printed this design yet, but I plan to use high...

I'm using 25.4mm/1" square steel tubing and the inside size is about 22.2mm. Make the inside size slightly larger near the center and then taper it down to the end, which means you might need to tap it in for the last bit. It also means it may be...

As it is I use the slic3r PE 1.41, which has a feature to click a face and make it the bottom. Here's what I'm using for 1"/25.4mm steel tubing: center cube: 24.6 protrusion: center: 22.6, end: 22.2, length: 33 spacer: 5 rounding: 1.5 Print...

... ...The new version was specifically designed to improve printability and created using Fusion360 instead of OpenSCAD. A .stl file is provided, which should work seamlessly with 1/2-inch (12.7mm) square tubing.

Create a modular square tubing tower by printing individual parts and connecting them via bridges. Adjust scaffold lengths for each piece to ensure proper assembly, while staying within your build volume. For stability, bottom pieces should be wider....

... 2 and 4. This should ensure opposite sides are parallel but does not guarantee the tubes are square; they could be parallelograms in cross-section. ... Print Settings Printer: MyKossel 1010 Rafts: No Supports: Yes Resolution: 0.2 Infill: 25%

People are printing a "T" bracket for 1-inch aluminum tubing using 3D technology. This 3D-printed bracket is actually lighter than its steel counterpart, thanks to its excellent material properties. The parts are printed in vibrant red PLA with...

The tube can be milled from 4 sides - just be sure that the cut of the tube is square to avoid missalignment of the 25mm bores for the guiding tubes. I also designed some new belt clamps to fit on that aluminum part. Print 2 of the clamps and 1...

Used to make rigid structures with 3/4" square aluminum tube, for a 3d printer frame. ... Instructions Print at a high infill density for strength

... math was wrong and printed out one of the original files. ... (wasn't 1/16" gap) So I added a file with 1/16" walls and left the 1/32" wall version. 3/4" Aluminum Square Tube Bushing with 1/16" Walls 3/4" Aluminum Square Tube Bushing with 1/32" Walls

This cap is designed to be compatible with 2-inch, 18-gauge square tubing. ...To use it, simply print and insert into the tube for a perfect fit.

I designed this adapter when building a low-cost printer frame that required two (or three!) twenty-millimeter aluminum square tubes to be securely attached. You can see their intended purpose in the accompanying photo, even if it's not presented...

... using similar syntax and style. ... Last year, our First Robotics Competition team, FRC (3840), utilized these custom-built hollow aluminum extrusion caps for various purposes. ...I'm resurfacing this information so that it complies with rule #13D.

This package includes the entire set of nine possible square tubing connectors and a specialized tool to assist in finding the perfect fit for your tubing. The default STL files are specifically designed for use with 1/2 inch (12.7 mm) square tubing,...

I designed an adapter to fit common office-chair casters into square steel tubing. This adapter is suitable for use with standard 7/16" caster stems and 16-gauge 1 1/8" steel tubing. I used it to attach AGPTek locking casters to the base of a Traeger...

Used to hold a caster in a 1" square tubing leg

Also provided is a special fixture to allow you to find the optimum fit for your tubing. The default STL files include all the fittings for 1/2 inch (12.7 mm) square tubing. The inner dimension of 9.4 mm should provide a nice snug fit. ...If not, the...