altoids razor case 3d models

In such cases, even the smallest amount of stringing will cause them to attach in an inconvenient way. Some of the islands are so small that it's even difficult to tell where to trim. For example, the very last island on the Fire Nation island chain...

For the clear parts, I recommend printing at 100% infill, and in the case of the lamps, printing with a brim instead of a skirt. The two lamps with the dome on top of the housing will also need support. After printing make sure to paint the...

However, you can also insert a pause at the end of the pocket and insert the pin during the print.I am leaving the original axle up in case someone is using a stronger print method or wants to make a remix, but please do not use it.Thus was born my...

The box is ~160x100x50mm. I've included the Fusion 360 file in case you'd like to make some changes. Please post your makes if you decide to print one. Print Settings Printer: Wilson TS Rafts: No Supports: No Resolution: 0.2 layer height, 0.6...

Knobs Collection for Bolt Hex head and Nut This Hex Bolt Handle Set ISO 4014-4017 M2.5-M10 Links to used components: ISO 4017 Bolts Nuts AB Glue Epoxy Super Glue 502 E8000 Strong Liquid Glue Links to used tools: Mini Wireless Grinder Polishers...

(Print with supports, it's slightly adjusted because the mounting arm can't move up much further unfortunately, as that would interfere with the slot for the hotend and thermistor wires) In case you don't have any type of sensor but for some reason...

If I mirrored the front design to the sides that would be good, but it's a bit more expensive and then I'd have to relocate my motherboard external case as that's in the way on that side. The other issue with lexan is you have to figure out how to...

The frame will accommodate phones up to 170mm tall x 84mm wide, and cases up to 13mm thick. It can be used with phones as short as 130mm.Lighting ArmsThe lighting arms screw into the corners of the frame with the frame screws. Note that on the side...

I am constantly looking for a place to place my pipes when I was done practicing except my case. I used a bed in my spare room until my wife decided I could no longer do that. A band mate, who was having a similar problem suggested a stand to hold...

It's not always easy to find two that are exactly the same, as it was in my case. If possible, make them with flexible PLA for more comfort. I've added more face mask arm link lengths. The size goes up about a cm as you go up in version. I've added...

This is the companion piece to the spool holder: https://www.thingiverse.com/thing:2543519 The mesh with each other using a T-Slot. Designed for a CTC Dual (might fit i3 replicator, Makerbot Dual?) with 5mm laser-cut wood panels. OnShape link:...

With an M3 nut of choice in case someone doesn't have an M3 insert.3. With a 3x12mm screw. -----------------------------------------------------------------------------------------------------And as always with functional rather than decorative...

4, 2023 : “motor-gear.stl” is modified to add a 1mm collar, for the case of loose fit to the motor axisNov. 18, 2023 : Code is improved to directly input the compensation value of clock speed in seconds.Nov. 18, 2023 : Optional files are deleted to...

As a supporter of the Kickstarter for Dinosaur Island: X-treme Edition and the Totally Liquid expansion, I faced the same challenge everyone else has been dealing with - finding a way to store all this content in one box, or worst-case two boxes? ...

This is an insert / organizer for the collector’s box of Architects of the West Kingdom.  It holds the base game, Age of Artisans expansion, Works of Wonder expansion, the promos included with the Collector’s Box, the five extra player mats from...

Put some glue into each of the holes and insert the tiers and the brush holder or the back spacer, in case you're not using the brush holder, so they're pointing up. Insert glue into the slots on the second side (or the center) piece, then put that...

In my case I am running this with a GRBL control board. If you want to use my electronics board, use Fritzing (see: https://fritzing.org/ ) to open the file uStepperV4_OpenLoop_Interface_V1.fzz. The board allows for a tidy installation on the arm...

In that case, I used (2) 1.5 volt battery series with a boost converter. I just didn't remove out the code for the wired version, but nonetheless it works the same. *** Remove the two comment slashes from the "Includes" at the top of the sketch....

I'm not including it here in case you want to use Meshmixer or the like to "emboss" some other letter. DISCLAIMER You know the drill. You are printing something on your printer. You are responsible for what you print. Don't give spinners to kids,...

This should not be necessary normally, but in case of any issues... On the bottom of the block I added a side gantry that may help to cool the filament and drive gear better, and provides an escape route for shavings when clearing the drive without...

... cooled down.&nbsp;</li><li>Do not use the g-code file on other machines than MK3S+ ! In any case, I recommend you to slice the .stp files by yourself to make your own g-code files.&nbsp;Have a nice print !And don't forget to like, rate and donate !

The case thickness will be 1.8mm and the tag thickness, height and corner radius are 3mm, 80mm and 7mm respectively. The QR code will also have round corners with a radius of 2mm. Additional holes will be included in the design with a radius of 10mm...

As long as your center hole and center bolt pattern is actually on center, this will be the case. Once the top print is bolted in place, take a sharpie and mark the template for the intake tube hole. Unbolt the top print and cut out the marked...

Uploaded here in case anyone prefers this version. [12 June 2018] Added some photos of V2. The red/pink bits are a glued-patch due to my printer stopping 8mm before finishing that part :( If you look closely, you'll see a fair amount of hot-glue to...

This looks much better (IMO), it does not block the view of the RAM (RGB go brrrr), it also frees up a more direct airflow path toward the CPU cooler (admittedly while blocking more of the top fan), and it makes the HDD itself less visible in the...

In many cases the filenames include suggested print settings, but use common sense (or ask me if you have trouble). The pictures have been ordered in a reasonably sensible order now, with the STL previews being the parts themselves, followed by a...

The clock attaches to the protruding M4 screw heads using they key holes at the back of the clock case.Uses T-Nuts for a very secure hold and easy printing. The clock attaches to the M4 BHCS using the key holes on the back of the clock.</p><p>Read...

...3D printing deals with heating mostly flammable plastics to high temperatures, thus it produces risk of fire in case of hardware failure. To decrease risk of fire, I recommend to print any head only with ABC/PC filament (don't confuse with ABS). 2.

I'm posting V1.3 in case anyone wants to try it, but I want to make it clear that V1.3 has not yet been tested. I do plan to test it myself sometime if no one else tests it first, but as of this writing (3/21/20) I haven't. If you decide to try it,...

The `.scad` file is included with this model in case you want to modify any of its design parameters; more information on how to do this can be found in the PPP [Puzzle Modeling tutorial](https://www.puzzlehub.org/tutorials/puzzle-modeling). ###...