altoids dac 3d models

Expandable under desk storage for O2 dac enclosure form factors. To Do: - Probably should switch the nut and bolt side of things for easier assembly - Counter bore screw holes so part is less prone to cracking. ... - Add removable faceplate to...

An upgraded Pibow enclosure, incorporating extra layers, accommodates a Raspberry Pi and HiFiBerry DAC. Employ the base and lid plus layers one through four from the standard Pibow set, or fabricate all new parts. ...Drill holes with 3mm diameter for...

This is a case for an old Raspberry PI 1B with an audio DAC. I created this case because all Raspberry PI 1 cases I found did not provide a clean design and left the SDCard accessible directly from outside. ...I'd prefer to have it integrated into...

This is my first project, a case for a Raspberry Pi 2B and a HiFiBerry DAC+ Pro. The uploaded lid does not contain my personalization that can be seen on the photo. ... Project details can be found here: [Blog post on...

This is a little slide in mount that I'm using for my FiiO E07K DAC. It was designed in OpenSCAD, so it should be easy to configure it for devices with different dimensions. ... OpenSCAD Source available at GitHub Desk Mount For My FiiO E07K at...

You will need: -Meanwell 5V PS (https://www.amazon.ca/gp/product/B005T6UJBU/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 -DAC (for superior Audio Processing)...

You will need: -Meanwell 5V PS (https://www.amazon.ca/gp/product/B005T6UJBU/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 -DAC (for superior Audio Processing)...

The IQaudIO Pi-DAC+ boasts an integrated headphone amplifier, as well as RCA line-outs, making it a versatile choice for any audiophile. The case can be positioned in multiple orientations to suit your needs. While the optional bumpers are not...

A simple case for a Pi Zero/JustBoom DAC Zero. Top and bottom lid are the same. Print instructionsCategory: Electronics Summary A simple case for a Pi Zero/JustBoom DAC Zero. Top and bottom lid are the same. Print Settings Printer Brand: Monoprice...

This is a holder/stand for the Arctis Nova Pro DAC so that it is raised and slightly angled.I used to use a basic cube as a stand for the DAC before but it was cumbersome to take out the battery and it looked kind ugly so i thought I'd 3d model a...

Bigger knob for potentiometer (6mm shaft) on FiiO E10K (USB DAC and Amplifier). 23mm wide, making it easier to turn. The photo shows the original on the left for comparison. When off, white notch faces down at 45° from left, like traditional volume...

I created a quick model so I could attach my FX-Audio DAC x6 to the bottom of my desk. The desk already had screw holes in it, making installation a breeze. The model is far from perfect, but it gets the job done. As you can see in the picture, I...

Variants: Blackout - No OLED, No Knob Blind - No OLED, Yes Knob Control - Yes OLED, Yes Knob Lockout - Yes OLED, No Knob The unit does not need to be mounted to the wall, and can be used to stand up the DAC if desk/shelf space is very limited. ... All...

A simple box for my I2S Audiophonics DAC from IKEA Dragan Bamboo toothbrush holder. Front cover is printed with zero top layers, and Hilbert Curve infill. Filament used for frame: Azurefilm 40% wood, Pine. Front cover: first 3 layers Azurefilm...

shoutout to Muddymaker (https://www.thingiverse.com/muddymaker/designs) for making the treble clef, you can find that .stl here: https://www.thingiverse.com/thing:4596430/files I designed the base to fit my Zen DAC, i printed it using wood PLA but i...

You must unsolder the connectors from the HifiBerry DAC+ PCB or carefully remove the contacts and case of the connectors (warranty will be void in either case). I made a mistake with soldering - lead-free and impatience don't mix well - so I had to...

Dropping this DAC can result in the knob and potentiometer becoming apart from the board. This part is designed to protect the knob while not using a lot of filament. Simply align the inner notches with the first hole on the side of the DAC case. The...

This project enclosure is designed specifically for housing the Phantom YoYo PCM2704 USB Digital Audio Converter (DAC) Circuit Card Assembly (CCA). Two distinct components comprise this enclosure: (1) a box with sides and bottom, and (2) a snap-fit...

This board simplifies switching between oversampling and non-oversampling modes for DACs or CD players featuring Philips SAA7220. As opinions differ regarding which mode is superior, this product enables personal evaluation. Technical details can be...

Case for a Pi Zero W with a Hifiberry Dac+ Zero, featuring an optional soldered 3.5mm audio jack on the Dac+ Zero (see images - white one has jack). I included a version that utilizes M3 2-3mm screws to secure the pi, but note these are a very...

To hold the housing and separate the RPi from the DAC, I used 8 M3 x 12 nylon screws, 4 nylon M3 nuts, 4 M3 x 12 spacers, and another 4 M3 x 6 spacers. The RPiZeriDAC-new.lyz file is included and can be directly used on LaserDRW with the K40 Laser....

Boite pour Raspberry PI 4 et carte HifiBerry DAC+ DSP. Il n'existe pas de boite pour cet ensemble. Pièces nécessaires : - 4 entretoises de 12 mm (M2.5) - 4 entretoises de 8 mm (M2.5) - 4 vis M2.5 - Colle prise rapide Dans un premier temps il faut...

For added functionality, I opted for the Pimoroni pHAT DAC for Raspberry Pi Zero, which provides high-quality audio output. Breaking with conventional design choices, I prefer to use 2.5mm nylon standoffs instead of the original hardware. These can...

Poor audiophiles like myself can barely afford a single Benchmark DAC. How could we possibly rack-mount it safely? <strong>If you have the metal joining plate</strong> this is everything else you need to fill the half-rack gap.</p><p>I have a few...

I built this super-cheap "DAC" using a really affordable mp3 player I had just lying around, along with a 6j1 preamplifier that I hadn't used yet. Needed parts: * MP3 audio module (usually sold for less than $2) * RCA female connectors * 9V Power...

I recall seeing something similar to that using foam in a well-known scientific publication, which inspired me to create my own version.

I have seen others make inserts but not ones that would be splash or dust resistant . ...this uses a 1/8 or .125 dia rubber foam seal it holds it in a channel along edge and seals against lid only.

Cases designed specifically for the Raspberry model 1 are now available, as well as versions tailored to the Raspberry model 1 paired with a Hifiberry DAC board and those optimized for the Raspberry model 1 coupled with a Hifiberry EXT DAC board.

Divided 75/25% along box width and 50/50% along one half of box length. ...More altoids stuff https://www.thingiverse.com/penguinfeet/collections/altoids Post-Printing Post a make Category: Containers