alp switch 3d models

I had a bunch of Alps switches and needed arcade buttons.

I was in possession of several Alps switches but desperately required arcade buttons.

I had a bunch of Alps switches and needed arcade buttons. Category: Video Games

Insert the switch mechanism into a wooden handle, securing it firmly, to eliminate the need for disassembling the top and stem components of your ALPS switches later on.

A simple tool to open up Alps and Matias keyboard switches.You'll probably want to print my new switch opener tool instead of this one: https://www.printables.com/model/201337-alps-switch-opener-v2

A simple tool to open up Alps and Matias keyboard switches.You'll probably want to print my new switch opener tool instead of this one: https://www.printables.com/model/201337-alps-switch-opener-v2

This is an ALPS switch example with low precision, serving only as a simple reference and not to be relied upon for exact values or measurements. The measurements were taken using a caliper on an old switch lying around. In essence, this is an...

This module is specifically designed to help users create a custom switch plate for their keyboards featuring Alps switches. The switches securely fit into place without any noticeable wobbling motion. ...I have personally tested this module using both...

This is a little tool to remove Alps switches from plate. The shell goes over the switch bottom housing and pushes on the little retaining clips, the slider goes in the shell to push on the switch and release it from the plate. ...This lowers the...

Configure switch activation timing: The Alps Switch Opener File allows you to set the exact moment when the switch is activated, ensuring smooth and uninterrupted printing. ... By following these guidelines and utilizing the Alps Switch Opener File,...

It's a bit tricky and isn't nearly as fast as taking apart regular Alps switches, but considering boards only have one or two locking switches it hasn't been enough of a problem to motivate me to design a dedicated tool just for them. Does it work...

... a dedicated tool just for them. ### Does it work with Alps clones? I've only used this with Alps and Matias switches, but as long as a clone switch has a similar retaining tab and slider geometry as a genuine Alps switch then it should work fine.

Switch out the original tester for a new one that's compatible with Cherry MX, Kaith, and ALPS switches.

A simple tool to open up Alps and Matias keyboard switches. ... You'll probably want to print my new switch opener instead: https://www.thingiverse.com/thing:5381785

This is a lube station for Alps SKCL/SKCM series Actually this is usable, but maybe to much flexible. Also there is a « test » file to test the fitment before printing the whole part. ...Considering that this is a file from a previous iteration, it...

This is a lube station for Alps SKCL/SKCM seriesActually this is usable, but maybe to much flexible.Also there is a « test » file to test the fitment before printing the whole part. ...Considering that this is a file from a previous iteration, it can...

In the strengthened variant, the outer legs of the switch puller are slightly beefed up to compensate for prints using flexy materials such as PP and nylon. The bearing interface has crush ribs and is designed to be medium firm. ... Bill of...

Designed to be printed without supports, flip the 3D model file upside down.

It bears some resemblance to the authentic version, yet it deviates in significant ways. ...However, this discrepancy doesn't compromise its functionality whatsoever.

Added "mouse ears" to the points on the opener to allow for better printing of the sharp tips on this file. I sincerely suggest printing in PETG. ...PLA will work; but it will snap after some use,

Face plates from various streams have been repurposed and tailored to accommodate Alps switches, while retaining a similar aesthetic appeal. ...The printing parameters mirror those employed for the GlowStream Cheap Mini Face Plate.

This plate fork is 3.5mm thick. ...It is designed to provide support for Mechanical Keyboard Plates that supports ALP/ALP-Style Switches.

Compact key fob designed specifically for securing Matias Alps keycaps.

Keychain to hold an Alps/Matias keyswitch Print instructionsCategory: Keychains Summary Keychain to hold an Alps/Matias keyswitch Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 mm Infill:...

Adapter to mount and glue in an alps funky switch to an existing 13mm hole 2,95mm high to make a tight fit and good glue contact to a 3mm carbon plate print with 0.1mm layers

I have installed Matias linear switches with replaced springs (reduced from 35gf to 12gf). The most notable change was relocating the external columns higher up, making it easier for pinkies to reach them. The thumb cluster has been reduced to two...

By modifying the Turnigy 9x with the 6pos mode switch, I discovered the inconvenience of installing large potentiometer switches on my Alps rotary switch. The smallest suitable knob is ideal due to its minute indicator pocket, which can be marked...

This is a straightforward adapter for incorporating Micro Switch keycaps, specifically those with a distinctive square-cutout design, into Alps key switch systems. ...Printed with an Ender 3 and PLA material, these adapters offer a seamless fit on both...

Tested, functional.

This one: https://github.com/foostan/crkbd Only 1.2mm thick (Alps specs) so be careful getting them off the bed. However, the switches snap in nicely. They do bend a bit so you might need to sort that out during soldering. Try increasing bed and...