akk vtx 3d models
5700 3d models found related to akk vtx.
thingiverse
The components that the support is tailored to are: Receiver: FrSky X-Mini or FrSky R-XSR VTX: AKK for stacking Barometer: BMP280 To secure the VTx, I employed the standard nylon nuts with M3 screws. ... (Note: This output has a Flesch-Kincaid grade...
thingiverse
Tiny lightweight VTX adapter for the GnarlyFPV Primo. ... Supports most Triangle style VTX units.
thingiverse
This mount allows you to use an MMCX90 connector with your AKK infinite DVR without worry of it moving or coming out.
thingiverse
Work-in-progress Tracking system https://www.virtualpilot.co.uk/index.php?route=product/product&product_id=59 Rx module https://www.amazon.com/AKK-Diversity-Receiver-Compatible-FatShark/dp/B07L2D6FSN (Don't be hating on the colors! ... I was using up...
thingiverse
Eine längere Version von dem Antennenmount für den Slayer One von VTX Slaye https://blog.sigsegowl.xyz/vtx-slayer-one/
thingiverse
This is a quick release mount for analog RX that connect to the dji fpv goggles. ... This version is for the AKK Diversity RX 5.8G. ... You will need to purchase "URUAV 5.8G RX PORT" and a analog RX.
thingiverse
AKK A5: https://www.amazon.com/AKK-Transmitter-Switchable-Quadcopter-Inductrix/dp/B073WV3HLS/ref=sr_1_7?dchild=1&keywords=micro+fpv&qid=1605128911&sr=8-7 TA SC28:...
thingiverse
AKK A5: https://www.amazon.com/AKK-Transmitter-Switchable-Quadcopter-Inductrix/dp/B073WV3HLS/ref=sr_1_7?dchild=1&keywords=micro+fpv&qid=1605128911&sr=8-7 TA SC28:...
thingiverse
This simple yet effective antenna mount leads the standard AKK X2-Ultimate pigtail up, allowing FPV antennas to be mounted with ease. To secure it in place, I used double-sided foam tape on my AR wing and found that it adhered very well. ...For extra...
cults3d
Decorative cover for analog fashion, suitable for AKK receiver. It is installed very tightly, it does not unfasten even if you lift the glasses by the lid. ...You can contact me and I will draw a cover for your receiver, you must have the dimensions of...
thingiverse
This is a mount for the Heng Long t34/85 tank. ...It uses a 10x2.6mm magnet to stick to the tank. Will need to add grip to the front, i use blue ummagrip. This is for the AKK a3 camera.
thingiverse
This design is tailored for the AKK pigtail and FrSky R9MM Antenna specifically. Although I implemented it on my Alfa Monster, I opted not to use the original standoff instead choosing these: Suleve M3AS9 10Pcs M3 40mm Knurled Standoff Bolt Aluminum...
thingiverse
... working altogether. Fearing another costly mistake, I decided to take the plunge and try out the AKK A5/Wolfwhoop Q2. ... With my custom front mount in place, my drone now weighs a respectable 41.55 grams without the battery or prop guard attached.
thingiverse
A simple case for the FPV Camera AKK KC53 It is LEGO compatible so you can just pin it to your Lego RC vehicles and off you go! The case gives the antenna a nice amount of support. I added vents, but I can't say whether the camera might get too...
thingiverse
Modelled Canopy around Camera Mount Version 1: Modelled Canopy around Camera Mount Version 2: Canopy with Upper and Rear Protection Version 3: 2.5g - Adjustable Camera Support Clamp with 2mm Screw Version 3.1: 2.8g - Expanded Mounting Arms Protecting...
thingiverse
This has been created because I couldn't locate a camera mount that would fit my AKK AiO-SA. ...I believe it comes with a universal press-fit mount for all AiO cameras, featuring standard 25.5x25.5mm mounting holes.\r\n\r\nIt's a 25* mount but I'm...
prusaprinters
This is designed for the AKK pigtail and FrSky R9MM Antenna. Even though this is used on my Alfa Monster I did not use the original standoff, I replaced them with these:...
thingiverse
For cooling purposes it is open in the bottom, so the vtx touches the frame, and also the top. ...For safety I use a zip tie and secure the board with a bit of hot glue.
cults3d
For cooling purposes it is open in the bottom, so the vtx touches the frame, and also the top. ...For safety I use a zip tie and secure the board with a bit of hot glue.
thingiverse
I got the BetaFPV F3 with OSD board and AKK A5 camera and realized the lens portion of the camera was barely large enough (<14mm) to squeeze between the hoops on my E010S frame, so I started with a simple existing mount and designed this (Sorry,...
prusaprinters
A simple case for the FPV Camera AKK KC53It is LEGO compatible so you can just pin it to your Lego RC vehicles and off you go!The case gives the antenna a nice amount of support.I added vents, but I can't say whether the camera might get too hot at...
thingiverse
My Custom Antenna Mount For The AKK X2 Ultimate. After wrestling with the antenna, I came up with a solution - this custom mount! It works flawlessly and weighs hardly anything, as long as you have it facing forward to minimize drag. To avoid...