akk a3 3d models

Works seamlessly with micro Whoops and securely cradles the Akk A3 vtx transmitter.

Based on Eachine TX03 FPV Case by raar (mirrored). ...External dimensions identical to the original. Case designed specifically for AKK A3 mini FPV camera, 5.8GHz frequency: AKK-A3-5-8G-40CH-VTX-0-25mW-50mW-200mW-Switchable-600TVL-1-3-Cmos

The original concept for this mount can be found here: https://www.thingiverse.com/thing:2028741 However, I discovered that the original TX01/TX02 mount wouldn't fit the AKK A3 due to its larger lens clip diameter. My design also includes little...

This is a mount for the Heng Long t34/85 tank. ...It uses a 10x2.6mm magnet to stick to the tank. Will need to add grip to the front, i use blue ummagrip. This is for the AKK a3 camera.

The A3-OSD necessitates a custom skeleton housing due to its mechanical distinction from the standard A3 camera. ...To ensure reliable operation, I recommend printing with ABS plastic since excessive heat generated by the camera can compromise PLA's...

The A3-OSD is mechanically different to the standard A3 camera, so I made a special skeleton housing for it. ...You should print in ABS as the camera becomes too hot for PLA, depending on output power setting, Print Settings Printer: Anycubic I3 Mega...

The A3-OSD is mechanically different to the standard A3 camera, so I made a special skeleton housing for it. ...You should print in ABS as the camera becomes too hot for PLA, depending on output power setting, Print Settings Printer: Anycubic I3 Mega...

<p>Are you looking for a sub $20 mod to bring life back to an old brushed on road rc car and make even a driveway difficult and a challenge to drive? ...Then your in luck</p> <p>This fits 6mm body posts with 65mm spacing</p> <p>Runs off the servo output...

Want a sub $20 upgrade to breathe new life into an old brushed on-road RC car and make navigating a driveway a thrilling challenge? You're in luck. This upgrade fits 6mm body posts with a generous 65mm spacing. ...It runs seamlessly off the servo...

Are you looking for a sub $20 mod to bring life back to an old brushed on road rc car and make even a driveway difficult and a challenge to drive? ...Then your in luck This fits 6mm body posts with 65mm spacing Runs off the servo output of a rx channel...

Introducing the AKK BS2 All-In-One camera and video transmitter mounting bracket, specifically designed for TinyWhoop style/dimension quadcopters.

Voici une modélisation du VTX AKK X1, identique au X1P, mais ce dernier possède une connexion d'antenne soudée avec un câble coaxial.

Simple socle pour le refroidissement du AKK Race Ranger matériel: 2 ventilateur 30x30x7 https://www.amazon.fr/gp/product/B096S3NBHT/ref=ppx_yo_dt_b_asin_image_o00_s00?ie=UTF8&psc=1 8 filetages femelle M3 3x4x5...

I designed this case for the AKK Diversity Receiver for my FPV goggles. I used 4x 3mm x 8.5mm screws to hold the two parts together. There is a small amount of XY slop as I have found that the boards vary in size and location relative to one...

For AKK Ultimate X2 direct mounting on the surface.

AKK Race VTX and antenna mount for ZMR250 frame.

AKK-SA Universal AIO Camera Mount for 36mm Boards such as Crazybee F3/F4

Support for the AKK Race Ranger, I glued it under the wing of my Ranger 1600 with hot glue. ... I screwed it with M3 screws ;)

This is a mount for AKK X2-ultimate VTX Its very light and I have included lots of holes either for screw mount or for cable tie mount.

This is a mount for AKK X2-ultimate VTX Mount . ...It has lot of holes for either screw or cable tie mounting

... the extreme temperatures reached by the video transmitter. This mount is specifically designed for the Akk X2 Ultimate video transmitter. ... PETG is the preferred material because it can withstand the high heat generated by the video transmitter.

this is a mockup of the FPV Camera AKK KC53 e.g. ...for further case designs sizes and dimensions have been measured carefully I`ll be happy to get feedback once you used it ;)

this is a holder for a video transmitter AKK FX2 UlTIMATE and ainav radar ESP32, it protects quite well in case of crashes. ... jest to uchwyt na nadajnik wideoAKK FX2 UlTIMATE i radar ainav ESP32 , dobrze chroni w przypadku awarii.

simple AKK fx2 ultimate mini mount, use two M3 screw that take in the PLA for the vtx, and two Ø3 wood screw to fix the mount in the plane. The button is still accessible and the space guarenti the cooling. ... Picture in action coming soon

Mount the AKK Nana 3 VTX securely.\r\n\r\nThis design worked well with the Mobula7 and should also suit other 65/75mm Whoops.\r\nThe mount holds one corner of the VTX while the other is fastened to the frame using a screw.\r\n\r\nTwo holes are...

Mi A3

practice3

Customized version of https://www.thingiverse.com/thing:247436 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=247436

Customized version of https://www.thingiverse.com/thing:58776 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=58776