akg n60nc replacement parts 3d models

This part is intended as a direct substitute for a component on the AKG N60NC, which unfortunately has a reputation for being prone to breaking. ...However, AKG remains reluctant to acknowledge that this issue may stem from a flawed design rather than...

I'm replacing two broken parts on my headphones, namely a switch disc and a headband anchor. 1. Switch disc: this small component keeps the headband together and presses the mute button when you remove the headphones from your ears. It must be...

You can use this part on your broken AKG earphone. It is fully functional. I made it a little narrow. ...If you place the metal part of the earphone after heating it, it will both settle and stick easily.

LR Replacement part

Replacement parts for AKG Y500Recommend to print with PETG for better durability, supports needed

Left and right covers for the AKG K121

I broke my AKG Y55 headphones' headband and decided to replace it with a new one that's not adjustable but similar to fully opened settings on the original headband. If you need to customize, check out the Onshape link:...

Cap/Lid for the right side of the AKG 240 (mk II) headphones that I managed to break since I didn't understand that you're supposed to remove the sticker and then unscrew the lid.I had best results printing it with a brim with the flattest side up,...

Replacement part for AGK K-171. ...Its a side clip, the external part of the one fixed (not movable).

This replacement slider washer is specifically designed for AKG K272HD headphones (part 5 "cover" in the original service manual, P/N 2040Z18020).\r\n\r\nWhen installing this part, it's essential to tighten it carefully since there are only a few...

This is a replacement headband attachment for AKG K272HD headphones that fits perfectly in place of the original plastic mount, securely holding the headband rods firmly in position. The original parts are made from brittle plastic that disintegrates...

# AKG K171 MKII replacement holder part This part aims to act as a substitute for the original holder, which failed some years after I bought this headset (which is great, as a side note!). It 100% replaces the old part (took me 3 iterations for...

This part replaces the original mount that holds the rotating ear cup on the AKG N60 headphones. After repeated use, this part has a tendency to crack near the screws. Installation: (1) Remove the broken clip by removing the screws and sliding...

Found a broken AKG K400, restrainer were broken. I designed new ones. ... All you need is 2 M2 bolts and nuts per side!

This is a microphone grill for my AKG D60, but it can be good for any other microphone. ...I tested with an AKG D 60 and with an AKG D65S.

This is a replacement cover for the AKG K240 MK-II, as the original plastic cover breaks easily. ...It is modeled to be as close as possible to the oginal part. Print laying flat with supports enabled.

The part replaces the cracked plastic on the outside of the headband mount for AKG K550 (MK1 - don't know if newer versions of the headphones are identical).Fits also to: K551, K553Tested for one year of hard daily use. No damaged parts.Printed only...

This is a Replacement Cover for the AKG K240 MK-II. The original plastic cover often cracks. ... Print laying with supports enabled.

Little replacement part for 2040Z0502 Since they are out of stock, i hope you find it helpfull ;)

Rather than shelling out $2.62 each for official replacement parts, I'm opting for a more affordable solution - using a cheap commodity hair elastic to replace the original factory rubber loop. But I'm not about to get creative by just stringing the...

Replacement parts for a Hummingbird Feeder.

You're getting your hands on some AKG K403 headphone components. The original instructions were pretty vague, but that's okay - you can print them out and give yourself a DIY makeover. ...Have fun with it!

Some replacement parts for the standard welding shield.

Replacement part for your Xouxou rope if you loose them... ...

Simple replacement parts for Senseo. ...Better print with 100% infill.

Some replacement parts for the standard welding shield.

Replacement parts for Clank! board game expansions. ... Print at least with 30% infill to add some weight.

3 replacement parts for Transformers Armada Optimus, parts that I was missing from mine Includes: super mode antennas/fins Battery cover Swivel mount for the blaster

3 replacement parts for Transformers Armada Optimus, parts that I was missing from mine Includes: super mode antennas/fins Battery cover Swivel mount for the blaster