ak 9mm 3d models

It was made thicker to accommodate the thickness of 9mm white foam window sealing tape. I've also added a piece that lets you print directly over a piece of cloth. This is basically a C-clamp that can be used to hold down thin clothing material to...

 I use 8.95mm or 9.0mm most of the time with PETG depending on the brand. Aluminum drill sleevesThese (K&S 3908) 9mm OD x 0.45mm wall aluminum tubes will also fit 8mm stepped ski bit and will increase durability of templates. Cut to ~¾" length. I use...

Make Flyingbear Reborn compatible with RatRig/VZBot and Eva 3D projectX: 348Y: 322Z: 340BOMM3x16 and M3 T nut: 8+ (better 14+) For rail adaptersX - MGN12H 400mm...450mmY - MGN12C 350mm...365mm (or any compatible with eva 3d project), for 400mm portal...

The only different part to adapt the Original Ender3_V2 (same base plate for Ender3; Cr10; Cr10S) Hot End, is to change the Green part shown below, it is called the Spacer 10mm high instead of 9mm. For the fans, it's up to you. Check this Thing for...

The inner hinge hole is 3.2mm whilst the outer is 2.9mm so the bolts should rotate freely in the inner hole. The reason for using the outer hole to cut thread through is so the device is less sensitive to how tightly you screw the bolts in and also...

Back to field 1: start from scratch, grab the documentation. Taking the measurements of the metal piece, the openbuilds documentation (measurements of the V-Slot beam and matching 23.9mm wheels), the ISO norms (M4 & M5 machine screws), I startet...

A Bach 42B inner slide fits widely available 15mm diameter tubes, but 14.9mm would be better - see github for improved designs that print without support. Check out https://soundcloud.com/pieter-bos-2013025 for a recording of both a regular brass...

Added a support for the loose end of the wheel cover. The dimensions are 27 x 13 x 9 cm A scale N version (1:160, 9mm gauge) is also included, to be made from 0.8mm Kraftplex. This comes as a puzzle card (108 x 65 mm) where all pieces are attached at...

I'm going to try 9mm or 12mm belts.. but this requires designing extra parts and at this time i haven't had the chance…The y carriage comes in 2 flavours.. the cnc machined beast.. or, the 4mm laser cut plate.. both more than triple the acceleration...

The Maxim 9 was SilencerCo's first fully functioning firearm and the world's first integrally suppressed 9mm handgun, representing one of the greatest strides made in both pistol and suppressor technology. (SilencerCo website) As the Maxim 9 is a...

A bach 42B inner slide fits widely available 15mm diameter tubes, but 14.9mm would be better. See github for improved designs for that purpose, that print without any support.</p> <p>See <a...

== Update 23-01-2021 (Added MZ-Gantry-adapter_1A-alternative2---Rev01.STL): A version in which the BLTouch mounting portion of the part is shifted 9mm forwards, made thinner and the right mounting hole is shifted 5mm to the left to have sufficient...

What is it : This is a box I designed to store and ship small and delicate parts. It has a number of goals / features : 1- Manage small parts 2- Protected from impacts and scratching 3- Protect from humidity during transport 4- Show product presence...

(See photo)●Sensor_back_cover.stl・A thermometer cover with a hole for pulling out the wire.・It is not necessary if you are using the original cover with additional cutouts.★Other necessary parts・2mm thick cushion tapeWhere I got it: Local home...

They are, usually, made from softer metal and after several dozen switches lose switching smoothness.Series: SR2511FProduct Category: Rotary SwitchesNumber of Positions: 2 PositionNumber of Decks: 1 DeckNumber of Poles per Deck: 6 PoleCurrent Rating:...

Steam pipes are PVC insulated mains cable and 0.9mm MIG welding wire provides rods and the strength of the roof supports. These are clad with U-section styrene. The motor and its mount are removed and the new motor is glued to a small printed...

On the new design, where the BLTouch is tucked into the rail spacer, the offsets are as follows: * Z Offset = 2mm * Y Offset = 25mm * Cyclops X Offset = 0mm * Chimera X Offset = 9mm from the left nozzle, usually E0 Other Notes: I designed the bolt...

This will be H-bot with MGN-12H rails and single 9mm GT2 belt. You may want to wait until this new project is completed and then choose between VertexEvo and Vertex-H. Here are the details https://www.thingiverse.com/thing:3145721 Update 26-Dec-2018...

20% or 30% would probably be ok with 1.5mm or better perimeter and 0.9mm face thickness. Thicker layer height makes for strong parts with better layer adhesion. I did 0.3mm layer height. You should not need to cut any zip ties, and will only need to...

Good stepper parameter starting point: 97.7 steps per mm, assuming 1/8 step drivers and 2.9mm filament. Retraction settings starting point: 7mm at 50-70mm/s BOM (hopefully complete): 1 x GRRF 3mm hotend,...

I'm now able to melt Geeektech filament at 15mm³/s instead of 9mm³/s with the original JHead, that's 67% faster. As melting filament was the bottleneck of the printer, I'm now able to print at 120mm/s, 0.2 layer height, and 0.5 weight without...

- The extruder fans end up being recessed 7.9mm from the front of the carriage. - The tips of the nozzles are 14.17mm lower than the bottom of the low parts of the carriage (where the screw heads meet the plastic). - Add unthreaded (or...

* it fits 25.5x25.5 mm AIOS * it can take motors with 9x9mm mounts (2.5", 3", 3.5" versions at least) * 4 and 5" versions take 9mm or 12mm motor mounts ! * 2" version takes 3 hole motors with 6.6mm mount ### recommended motors * 2 inch :...

(Thankfully the Pink for Breast Cancer Research set came with stations and extra trains.)I hope you enjoy this set as much as I enjoyed putting it together!Art Box:...

I needed to create some spring action to get a 9mm opening over a 10mm ball, without stressing the plastic so much as to deform / weaken it. I cut two slashes in the socket to allow it to expand. The plastic oval encompassing the socket acts as a...

I'm uncertain about the compatibility of this design with 1.9mm tubes. My new Capricorn XS tube is significantly larger than the specified 1.98mm, likely around 2.05 (stated as 1.9±0.05). Therefore, don't rely on Capricorn maintaining their...

No wast of plastic and printing is a breeze. Part needed to complete the build: 4 small piece of a break away 9mm cutter blade (used blade is plenty fine, you don't need a sharp edge) Instructions: Print everything. Take the middle piece and the...

Here's my first design of a fishing lure, designed for use with 2x treble hooks and a twisted wire frame/spine made from 0.7-0.9mm wire. There's also a pocket inside so you can add small ball bearings to make it a rattle bait, or to add weights...

rnrnUsing the LED strip, https://www.ebay.co.uk/itm/2-4-6X12V-LED-Car-Interior-White-Strip-Lights-Bar-Lamp-Car-Van-Caravan-Boat-Home/223067435724, slide the LED strip itself out of the thin black bezel surrounding it, to prepare it for fixing to the...

I used the un-threaded shank of a 180mm long M10 Coach Bolt, which has a shank diameter just under 9mm (8.94 to be precise), spot on for this purpose. You only need a small piece 11-11.5 mm long, which you can cut from the un-threaded section of the...