airtag remote 3d models
22974 3d models found related to airtag remote.prusaprinters
I also recommend vacuum sealing the remote and the print together and heating it with a hair dryer, massaging the part to fit, then waiting for it to cool completely before releasing the vacuum seal. This gave me a perfect fit.I designed it in Fusion...
thingiverse
Allows you to attach an AirTag to a Siri Remote. This is a different approach from my previous version (found here: https://www.thingiverse.com/thing:4847198). ... If you're looking for a similar design for the Siri Remote 2nd Gen, check out my other...
prusaprinters
Allows you to attach an AirTag to a Siri Remote. ...This is a different approach from my previous version (found here: https://www.thingiverse.com/thing:4847198). If you're looking for a similar design for the Siri Remote 2nd Gen, check out my other...
thingiverse
Allows you to attach an AirTag to a Siri Remote 2nd Gen. This is an update on my previous version which was designed for the 1st Gen Siri Remote (https://www.thingiverse.com/thing:4853986). Note: There is an original version and a v2 STL file. ...The...
prusaprinters
Allows you to attach an AirTag to a Siri Remote 2nd Gen. This is an update on my previous version which was designed for the 1st Gen Siri Remote (https://www.thingiverse.com/thing:4853986). Note: There is an original version and a v2 STL file. ...The v2...
thingiverse
After printing, just slide your Apple AirTag it into the slot and then slide the remote in. The longer version was needed for remotes for my TVs with integrated FireTV. Note this does replace the back cover of your remote. ... Remix of...
thingiverse
Designed a AirTag holder for the new (2021) Siri Remote for the Apple TV. Printing: Print standing up, charging port on the bed. I used a raft, but it's not required. AirTag fits nicely in the round part at the base. Hole on back to easily...
thingiverse
This is a simple airtag holder that slides over the bottom of the Samsung Smart Control remote. It fits snugly due to a .25mm tolerance. ... I was able to print this with supports only on the bottom of the airtag rim.
thingiverse
... it as-is, but it needs some refinement. Pocket is a bit large, and the thickness can probably be reduced a bit. Unfortunately, after adding this to the remote the remote is no longer quite as loseable, somewhat defeating the purpose of the AirTag.
thingiverse
... If you'd like to purchase a printed copy you may do so at https://www.etsy.com/IOMade/listing/1001781388/apple-tv-siri-remote-airtag-case?utm_source=Copy&utm_medium=ListingManager&utm_campaign=Share&utm_term=so.lmsm&share_time=1620955663716
thingiverse
When AirTags came out, it seemed like a perfect match (should've been a built-in function), but since they aren't flat, sticky tape would not work. Hence, this Remote Case. This one is for the new Apple TV 4K, w/Siri remote. I have two files here,...
prusaprinters
Hence, this Remote Case. This one is for the new Apple TV 4K, w/Siri remote. I have two files here, one with the AirTag on the back, the other on the front. One may be more comfortable than the other for you.</p> <p>Extra bonus, the plastic around...
prusaprinters
Suggestions welcome.I printed with a raft, standing up on the end where the hole for the charger is with no supports.If you'd like to purchase a printed copy you may do so at...
thingiverse
Got tired of my kids hiding the remote. ...Problem solved.
myminifactory
This isn't perfect yet in terms of sizing the place to put the airtag, but it's certainly usable and I haven't found a solution for this yet that I liked. Suggestions welcome. ... I printed with a raft, standing up on the end where the hole for the...
thingiverse
Designed a AirTag holder for the new (2021) Siri Remote for the Apple TV. Printing: Print standing up, charging port on the bed. I used a raft, but it's not required. AirTag fits nicely in the round part at the base. Hole on back to easily...
prusaprinters
You slide one side of the airtag under one of the “straps” and then use something thin to pull aside the second one.The airtag is held tight and not allowed to rattle around. I figured it might scratch the bottom of the remote even if it was...
thingiverse
I recommend installing an AirTag in the mount before gluing the mount to the remote. You could glue it with epoxy, or super glue, or probably Super 77. I used Super Glue and it stays very well. I used a small clamp to hold the mount on while...
prusaprinters
This is essentially a slight remix of the ‘Original Siri Remote Holder with AirTag’ by makanadumlao on Thingiverse: https://www.thingiverse.com/thing:4851515. I removed the lanyard holes and made it slightly more ‘no support’ friendly. I...
prusaprinters
This is because the remote will push on the sides of the holder to give the friction to hold things together. After gluing them together and having the glue dry, you turn it upside down and slide your AirTag in, then the remote. After that,...
thingiverse
LG Magic Remote control holder with slot for air tag for people like me that keep losing the remote.
thingiverse
I wanted to connect an Air Tag to a Siri remote. Designed this. ... Update: I've since designed a different approach after seeing someone trying to sell something that is more of a full wrap and it seemed like a good idea:...
thingiverse
Want to save your marriage? ...Here is a roky remote holder with AirTag slot. ... Print Settings: - Supports - 15% Infill - I recommend PETG
prusaprinters
Now find your roku remote with an airtag!!! It is also a quick print. Use my settings and it will be done in 3 hours (petg)! ... </p><p> </p><p>Print Settings:</p><ol><li>Supports</li><li>15% infill</li><li>recommend...
thingiverse
Didn't like any of the Apple TV Siri Remote Airtag cases, so I decided to roll my own inspired by a few of the other designs. ...Not a remix of any specific design, just similar in look-n-feel.
prusaprinters
This is the ultimate tracking case for your new-look Apple TV Siri Remote. If you already have a Siri Remote, this case is perfect for protecting it and keeping it organized. ...The bottom of the case features a slot for your AirTag, with a snug...
thingiverse
It takes one AirTag, "white side" out because the white surface seems to be the resonator for the speaker (putting it in the other way makes the "play sound" feature much less useful) I printed this with supports "open side down" so that the mating...
thingiverse
There are several versions of Roku TV remote, so this may not fit yours. The STEP file was included in case you'd like to adjust it to fit yours. The Airtag cover is still not perfect. Although it snaps in, it falls out pretty easily so I'll need...