airtag for airpods 3d models
3099047 3d models found related to airtag for airpods.
prusaprinters
Good for carabiners, or paracord that you can fasten yourself.May need to print at different scale to fit your airtag properly.At 100%, it wouldn't squeeze in, 104% was way too big,102% was still a bit too big,101% was a bit too loose for my...
prusaprinters
Collar Holder for Apple AirTag. Currently I have models for 20mm, 15mm, 13mm and 10mm dog/cat collars. If you need different size message me and I will add it. Require minimal supports to print, you can find support configuration in...
thingiverse
A simple case for a single Apple Airtag, with an opening at the top for a keychain or other loop. Held together by four M3 screws, which thread into the plastic on the bottom piece itself. Anything longer than an M3x8 will stick out in the back,...
prusaprinters
This holder could be attached with a cable stip at your bike or scooter or something else. It's unobtrusive, and if you stick a reflector on the lid, you can hide that there is an AirTag is inside.A little bit support is needed for the parts,...
prusaprinters
ZipTie holes are 2x5mm and there are a few drain holes as well.Designed for 0.32mm layer height, 1mm nozzle & PETG (since that's my current configuration :) ) but should work fine with smaller dimensions and other materials.No supports required,...
prusaprinters
Attach an AirTag to your coffee, and never lose a mug again! ...Set to notify when left behind.</p>
prusaprinters
I recommend to activate the option to print thin walls (attached screenshot of its location in prusaslicer) For a correct impression of the lower part of the lid, is recommended to use supports (if the finish of that area does not matter, it would...
prusaprinters
Print Settings:Material PLA, ABS and/or PETG Wall thickness of 3, with minimum of 25% infill suggested Moving tolerance should compensate for differences in printer calibration and toleranceChoose print set up with good bed...
thingiverse
Remix from https://www.thingiverse.com/thing:4849497 and https://www.thingiverse.com/thing:4850601 So that there is a more cardlike enclosure. ... Not tested as my Airtags have not arrived yet.
thingiverse
... for optimal results. ...Experts recommend a minimum infill percentage of 15% or more for maximum structural integrity. ...Secure the cable in place with a strong, temperature-resistant hot-glue adhesive to prevent damage and ensure a smooth finish.
prusaprinters
<p><a href="https://www.thingiverse.com/thing:4844511">https://www.thingiverse.com/thing:4844511</a> Remix</p> <h3> Print Settings</h3> <p><strong>Rafts:</strong></p> <p>No</p> <p><p class="detail-setting supports"><strong>Supports: </strong>...
thingiverse
There are four versions Those with Hexagonal cuts are for SLA Printer's only! ... The other are designed for FDM Printer.
cults3d
I designed this for SLA printers, but since I don't own one I couldn't test the printability either. ...There are two versions, where one has smaller hexagons.
prusaprinters
This device is for those that carries the macbook from home to work and always forget where they left the charger, ... ...and yes, you can be the one that could forget the charger in the Starbucks as well.</p><p>In the other hand, does your sibling or...
prusaprinters
Keyring cover for keyring Print Settings Rafts: No Supports: NoResolution: 200 Infill: 20 Filament: Ninjaflex TPU BLACK Category: 3D Printing
thingiverse
Airpods holder tool for easy battery replacement :)
thingiverse
**Slim Airtag Holder for Wallets** Designed so that the Airtag would be the thickest part of it and so the slopes follow the curves of the Airtag. This way you should't feel the Airtag when the wallet is in your pocket. Made to fit my Secrid Wallet...