air assist chine 3d models

Unfortunately, I did not find any air assistance model that could simply be connected to an aquarium air pump. That's why I designed my solution that suits me and is easy to connect. It was important for me to maintain an approach to laser sharpness...

This air assist for the Longer Ray5 10W module uses only two 3M screws to hold it in place. I used some 4mm Inner, 6mm Outer air hose.I printed it with a raft to help hold it down and you don't need to use supports if your printer has good...

K40 Air Assist with Omni Nozzle to give an even air flow and not cause soot/kerf to be blown in a single direction. Non-enclosed so you can still use a height gauge between the material and the bottom of the laser/lens. Made from scratch in...

Board for adding air assist to M50 ATOMSTACK module Fitted in place of the original glass, connected to a 4 mm ID hose. Available in two versions, closed or open. Can be connected to a tank compressor, regulating pressure between 0.5 and 1 bar.

(See remake by @gerhardbooysen for the NEJE 40watt module here: https://www.thingiverse.com/thing:4892305 ) After testing different solutions for air assist for my NEJE laser module, I found that the nossle system on my CO2 laser was the best...

The was an attempt to design an air assist nozzle for the K40 printer. The nozzle works with the existing laser head and attempts to utilize lamar flow. So far I have had decent success with it but have not tested to see if has increased my cutting...

I printed and tried various air assists for my laser engraver but I found most of them too bulky so I chose the solution proposed by Tine Sedej (https://www.thingiverse.com/tintek/designs). ... To the laser anchored support...

Air assist nozzle for NEJE 40watt laser module. I redesigned https://www.thingiverse.com/thing:4884993 to fit the Neje 40W (15W optical) module. You can use a push-fit or any other 2.5mm hose connector, or even drill it larger. I also...

An Air Assist Nozzle for the Stock Laser Head on the K40 Laser Cutter. The aim of the project was to design and build a lamar flow laser head to increase the cutting ability of the laser. ...Initial testing has not been started but if you print this...

Die beiden Teile sind die simple Konstruktion eines air assist für einen K40 Chinalaser. Als Luftzufuhr habe ich einen 8mm (6mm innen) Druckluftschlauch genommen und den durch eine Schleppkette mit 10x10mm gezogen (Amazon). Bei mir steckt ein...

Got the air assist for M1 love the magnetic nozzle but I don't feel safe, leaving the grease open to all the dirt and smoke, so I designed the cover so the nozzle can still be removed and the blade holder stays in place, personally, I haven't need to...

SummaryAir Assist Clamp and Cap for K40 Style 40W Chinese Blue and White CO2 Laser.Air assist clamp and cap designed specifically for K40 style lasers, ideal for a 40W Chinese blue and white CO2 laser.The clamp and cap are engineered to securely hold...

I remixed several parts so that I would have smoke assist while engraving, but also wanted air assist and smoke assist while cutting. This setup works well on my K40. The duct is sized for a 40x40mm fan. Assembled with four 3mm bolts and nuts and...

If you don't have a laser pointer, the air assist tube should be about 3 mm above your focal point of contact with the material. At the angle of the tube, the air is injected right at the point of laser contact in the groove. You'll find that you...

and since I wanted a simple and equally effective solution that is compact, I designed this Air Assist. Depending on the version, either 2 M2x8 or 2 M3x8 and 2 M2x12 or 2 M3x12 screws are needed ( whichever 4010 fan is used) to attach the fan and...

Carefully position the capped tube, secured firmly by clamp in place within the air assist mechanism, with the tapered end pointed at the calibration mark. ...Install and attach an easily sourced air source to complete this straightforward setup...

This is an air assist nozzle for the Longer Ray 5 Laser engraver. It accepts a 6mm outside diameter tube. Note: after installing this nozzle, you can no longer use the aluminium spacer to calibrate the laser. Instead, you have to measure from the...

brass tube for air assist tube 1 - 2 ft length of 4mm ID clear air tubing (and air pump of choice) 1 - m3 x 10 bolt and nut 1 - m6 drill tap 1 - 5/32 drill bit (9/64 is slightly smaller but could work for nozzle hole in length and side) Drill the .8...

An Air Assist Nozzle for the Stock Laser Head on the K40 Laser Cutter. The aim of the project was to design and build a lamar flow laser head to increase the cutting ability of the laser. ...Initial testing has not been started but if you print this...

Simple rear mounted air assist for the Ortur Master 2. The mounting bolts can be re-used on the fan mount, but you will require a 12v 50x50x15mm blower fan and a couple 25mm bolts and nuts to fit it. The stock mounting bolts are just barely...

I've tried various air assist nozzles on the market, but all of them have one major flaw: they interfere with a cross beam underneath the mounting bezel, making them unusable straight out of the box. So, I decided to design my own nozzle from...

This is an Air Assist Nozzle to be mounted at the TwoTrees Totem S Laser Engraver. It is used to provide airflow to the laser lens for protection and clearing smokes and fumes. The piece was designed to be screwed in with 4x M2.5 screws that use...

Up for your printing pleasure is yet another air assist for the Chinese laser cutter. I've incorporated a boss for adding a 6 mm pneumatic elbow fitting, perfect for macro line applications. This design features a 5mm opening for effortless airflow.

It is the new S9 model which has a black metal insert to create an air assist effect (poor) My S9 laser has a 19mm cavity that receives this insert. My piece should also fit the older S9 models if you have a 19mm cavity. The standard 4/6mm air...

So I decided it was time to start shopping around for a new supplier who might have better air assist systems in place. That's when I stumbled upon Epilog, and their setup really caught my eye. I figured I'd give it a shot, so I set out to recreate...

This is a set comprising of air assist nozzles with the following outlet diameters and clearance from the focus. This version has handy size labels embossed on the nozzles, a free version is also available on thingieverse without the embossing. :-)...

The air pressure is not just building up inside and goes wherever there's less pressure but directed outside. There's separation between the laser path and the air path inside. Make sure to set the focus BEFORE installing, as you won't be able to...

Side assist nozzle, to fit on an extension tube on a G8 Lense

This is Assist Mode activated on the Laser K40 system with a Nozzle Diameter of 26mm.

Using a larger fan (20x25mm outlet) and a 3D printed air cone dimensioned to suit the fan's flow and pressure capacity (air guide and outlet not being too narrow nor too wide) you get a good strong airflow. ...