aincrad 3d model

Finally, if your printer's bed is larger than mine and can accommodate the full required width of the inserts, you can merge the included additional bodies Body30, Body67, Body68, and Body69 with the corresponding model parts. The weight of each...

I would recommend all the bridges honestly. Update Jan 31 2021made the holes for the hex nuts smaller to promote better hold under torqueadded relief cut on the M6 hole, as threading may result in splitting the model on version D1resized the D1...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

All necessary supports are pre-applied to the models (there is no need to add additional supports). The main body of the stein/mug prints with cylindrical supports, the left/right lid have perforated supports, the lid top doesn't require supports...

The assembly of the upper part of the buffer is clearly described in Dave's files (please visit his thing on the Thingiverse (link above) and download the PDF file with the instructions or click the direct link ). Hardware needed for the base part...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_shape = 4 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

The bands were modeled separately so they wouldn't require supports and be stronger. I printed them on their sides and used a brim as they had less surface area. They will have to be glued. The main body and battery compartment required supports. I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

This is a well known test model with many remixes.However, I have not seen anyone with automatic temp range.Existing temp tower is “semi-automatic”, they set temperature to preset levels with custom g-code in “before layer change”This print set...

My Fusion 360 CAD model has 0.09mm of axial clearance so the printed threads should effortlessly spin together. Extruding over 0.09mm will make it extremely difficult to twist the nut and bolt together using fingers, so just reprint both parts with...

Furthermore I created the endstop mounts which are already present in the Fusion 360 model. I will try to update the pictures today or tomorrow. Now it gets exiting! Electronics are next! **Update 9** (03.07.2018): After test driving the Z-Axis I...

You just have to have the right case respectively.If you use the original MK3S+ frame check out the version for the original Prusa frame. FeaturesWorks with Raspberry Pi 3 and 4Works with any type of Armor-style case that uses M2.5 screws. Just...

Modified the vent slots on the right side so they are less likely to cause problems during print. I really liked the compact ATX benchtop PS by gdoniu93 and started out simply to recreate the model in Fusion360. Somewhere along the way (as it often...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

This model will do the same stuttering if printed too fast even with the used a reduced segment count (50) in the cylinders. The trusty SD card worked for me with a big batch of these. The other solution was to slow the print down.Let me know in...

If you do this, use the "Pusher Extd" model. To modify the solenoid: 1. Remove plunger. Remove about 3mm of the black base and sand flush with the metal slug. Sand the black base to make it slightly thinner if you want to add an additional spring...

It was hard to get some screws in it so I had to manually remove parts that model has removed for you. Make sure if you use screws to hold bearings tight, lowest ones have low-profile heads or they will be lower than extruder nozzles and hit your...

Most issues with these printers can be traced back to this strain gauge probe not functioning properly.It would be convenient if their mainboards were compatible with the CR-touch / BL-touch probe style sensors found on the newest higher end Creality...

This allows the flow rate to be tweaked only for the detailed layers [as described here](https://support.ultimaker.com/hc/en-us/articles/360013370140-How-to-adjust-print-settings-of-a-part-of-my-model-in-Ultimaker-Cura). Update 4/10/2022 (v4.2):...

This model drops excess wind The concept is to use it quietly This mod may be a bit more difficult 5015-24v fan 5015-12v or 24v fan * Please note that the polarity of the fan electrodes may be reversed. DC-DC adjustable step-down power supply I...

I have since printed out another model in ABS which I am hoping will be more durable. PETG would be another more durable substrate to consider using. Special thanks to Jim Harmon at Keystone College and Emmitt Zugar at Salem Community College for...

Finally you should set up channel mixing for tracked models in your transmitter. I added 2 photos of my mixer setup, but this video here explains it very well: https://tinyurl.com/bdns4pj5 It took me half an hour of trial&error negating channels...

I started with the photos of the metal models (I've uploaded those photos to thing:1618843) and went from there. All the design work was done in Moi (Moment of Inspiration). Once I had an escapement design, I ran it as a simulation (unsuccessfully)...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Any sagging of overhangs that occur at the very top/front of the model can simply be trimmed or cleaned away after. The mount can be either just press fit (if tight enough) or glued in place into the holes on the back of the body. I recommend gluing...

the vanilla singleplate model), though the pulleys included here are a bit different from those. Re-cut bolt/nut holes in the idler pulley holder and thumb wheel to accept M5 hex bolts (because those are all I have with hex heads :-P ) Added an M5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...