aeropress filter cap 3d models

This mimics the shape and size of the scoop that came with my Aeropress roughly ten years ago, I assume they still utilize a similar volume of scoop though I'm not entirely certain. Its capacity is approximately 38mL. Nowadays I use one of these...

Can be mounted with screws or double sided tape (3M UHB or VHB should hold the weight) Check out my Aeropress filter holder: https://www.thingiverse.com/thing:3409488/ Print instructionsCategory: 3D Printing Print Settings Printer Brand: Prusa...

To avoid the filter paper getting dusty or covered in kitchen odor I designed this lid for the provided, original AeroPress filter storage. It fits snuggly, I printed mine in ABS material, it looks so dirty in the picture because I didn´t clean...

It's engineered to securely hold the paper filter holder, stirrer, and scoop that come with the coffee maker, as well as one of the Able Fine Disk metal filters if you attach three copies of the finger STLs. The wooden post supporting the tool holder...

In my opinion the XL version of the AeroPress is pretty lackluster without this attachment. As far as I know ColorFabb HT is the only “food safe” filament with a glass transition point above 100° C and is absolutely necessary in order to use this...

Hello, I created this storage case for the Aeropress Original, I was inspired by the Aeropress Go - although it's not as compact as the aeropress go but then again the original is must bigger too. It fits in one hand and everything fits nicely...

Simple funnel for aeropress go, i design this using freecad

It's the Aeropress Cute & Gorgeous for coffee lovers.

Manual scoop holder for Aeropress prints effortlessly without support structures.

Tool to aid in the tightening and removal of the screw on filter cap.

Well, there is a lid option for the filters if you use those - the filter-pot-pins, coffee-lid-pins, and lock pins (x2) should be printed otherwise, the mesh can travel 'loaded' in the Aeropress. Then the whole coffee pot load slides into the...

A lid for the AeroPress coffee maker that closes the pressing tube opening, keeping spare filters or accessories in place without worrying about them sliding out. The lid fits snugly into a tube with an internal diameter of exactly 50 mm, requiring...

We required an ingenious and compact rack to dry our Aeropress efficiently. Design objectives: 1) Compact enough to fit comfortably on the counter (in our situation, atop the sink). 2) Holds securely the main body, paddle, and cap following rinsing.

... the grounds from the grinder to the AeroPress seemed like an extra and unnecessary step. ...This model allows the user to grind their coffee directly into the AeroPress when using the Conqueco rechargeable grinder. ... Works with AeroPress Go too.

Combine this with a thermos full of hot water and some ground coffee and you can make a cup of freshly brewed coffee anywhere. Grind your coffee into the container and seal it in between the chamber and filter holder. The plunger acts as an air-tight...

... re-spin this later so use a large o-ring to try and get an air tight finish. The container doesn't go all the way down so there is still room to stash a few filters in the plunger too. ... Please ensure the material you print with is food safe.

This will hold the two body-pieces of the Aeropress, as well as filters and the stir bar. The two back parts can be screwed and/or glued together (I used M3 screws). The arms should be a tight fit, but I might recommend gluing them in for good...

... with the Aeropress coffee maker. ...I printed it at 0.2mm layer height and 20% infill, no supports are needed. I recommend pairing this with the Aeropress Wall Mount by Kristianmedk https://www.printables.com/model/25247-aeropress-wall-mount 

The design uses genuine AeroPress Go stirrer as a part of the tamper.

This is an adapter to mount the coffee grinder (asin:B08YN9MSFG) directly onto the Aeropress.

This is gmarsh23's Aeropress Station, stripped of its handle attachments.

Storage stand for the Aeropress. ...Username has been removed for others to use.

Travel Lid for AeroPress - Enhance Your Coffee Experience on-the-go!

This is gmarsh23's aeropress station, just without the handles Category: Kitchen & Dining

A small component attached to your aeropress filter holder holds the measuring scoop/spoon and stirrer. Since it comes into contact with food-contact items, review guidelines on food safety for your printer and printed material. The example shown is...

... renders was sourced from the Fusion 360 library, created by Ryan Arnaudin. https://gallery.autodesk.com/fusion360/projects/aeropress-coffee-maker Print Settings Printer: Hictop 3dp11 Supports: Doesn't Matter Resolution: 0.03 Infill: 15% Notes:

Designed to compliment awesome AeroPress and Prismo organizer by **el_mapache** [https://www.thingiverse.com/thing:4884703](https://www.thingiverse.com/thing:4884703) and Aeropress Scoop holder by **robotra**...

... come with the funnel for loading coffee. I got tired of spilling coffee grounds on my counter when filling my AeroPress so I designed and printed a funnel to keep them off my counters. ... YouTube Link: https://www.youtube.com/watch?v=dIm9dIBCwto

... the wall and free up valuable counter space. The sleek design fits perfectly into any kitchen decor. Securely holds your AeroPress in place, making it easy to use and store. ...Perfect for small kitchens or offices with limited counter real estate.

So a set of 3 plus one lid should be enough.The compartments can hold up to 14g of ground coffee, more if you tamp it inside.I usually use 11g of coffee at a time.I advise to also print the Aeropress extension :...