aerogarden models

They take very little force to install or remove, but they will not fall out if you blow on them or if you take the grow deck out of your Aerogarden and run water over it or turn it sideways. ... Use the darkest color filament you have, preferably...

Seed growing pod for aerogarden. This was a scaled down version of an unpublished seed starter I made to make it easy to transplant into something else. The design consists of two halves that snap together, you can then fill them with your grow...

This is a stand for the Aerogarden Stem grow light. The grow light doesn't come with a stand that allows it to be on flat surfaces, only a stake that allows it to be put into dirt. So, I made this stand so I could use the light for my terrarium. ...

Yet another Aerogarden plug or blank for to cover slots that don't have anything growing to avoid algae growth in the water. This one has a cutout to allow for the water to easily go back into the tank. ... I print without support, 10% infill, but I...

Attach this around the stem of your Aerogarden plant to block light from causing algae and other unwanted organisms from growing. These must be printed with a flexible filament such as TPU. This is much better than the two-piece design I was using...

If you're leaving unused seed pod openings on your Aerogarden, make use of this cap to seal any holes not being utilized. This keeps light out of the water tank and prevents algae and unwanted organisms from growing in the water. The cap stays...

This cap is designed to seal unused holes in the Aerogarden Seed Starting Kit, minimizing evaporation rates after plants outgrow the protective cover included with the kit. They are engineered for a near-flush fit, ensuring a snug connection that...

How-to: https://www.youtube.com/watch?v=GBaolwXV0lw This is for my Bounty Elite, not sure if it'll fit other models. I tested it and it works great. No more low water alert. The top twists onto the floater. Make sure you follow my support...

How-to: https://www.youtube.com/watch?v=GBaolwXV0lw This is for my Bounty Elite, not sure if it'll fit other models. I tested it and it works great. No more low water alert. The top twists onto the floater. Make sure you follow my support...

Two types of aerogarden pod holders built into a wide mouth mason jar lid.

Seed starting trays designed specifically for the AeroGarden 3 hydroponic system come equipped with specialized seed starter plugs.

I couldn't find any AeroGarden pod inserts that would work with our Goodful model because they either hit or blocked the water spout (check out this picture). To fix this issue, I modified bandslinger's insert to ensure it sat perfectly flush and...

AeroGarden net pots are difficult to use outside AeroGarden, since their neck needs 33.6mm hole for tight fit. This slot fits in 1.5" hole and provides snug-fit for the AG basket, dome and cap. Now there is no reason to keep AeroGarden...

models

models

This remixes the previous design to allow the trellis to come off with the basin for changing water and two hook designs that easily comes off. I recommend the hook 2 as its simpler, although requires more filament. ...I also increased the holes to make...

So growing tomates in a harvest 360 is a bit of a chore. i waited too long to put this in but it is in now. this works great even for heavy loads. it is wide open enough that you can fill the water easily. There are holes at the back so you can zip...

I Design a Special Pod to Nurture Seeds. First, I Place the Seeds in a Germination Pod Where They Start to Take Root. Once Established, I Transplant Them into a Final Home in Peat Moss Pods. ... Print Settings Printer: CTC Dual Rafts: None Needed...

<p>I printed this at 0.3mm layer height. ...Set no top/bottom layers to save some filament, and for aesthetic purposes.</p><p>There is a divot in the bottom for a connector/alignment brace, but I never got around to making the actual brace.</p><p>You...

This is a remix of https://www.thingiverse.com/thing:1266845. This thing was created with Tinkercad and can be edited online at https://www.tinkercad.com/things/1rim9I5aPz8. ...Print Settings: Printer: Prusa i3 MK2; Rafts: No; Supports: No; Resolution:...

End Caps for Open V-Slot 2020 with Open Hardware logo. This is a remix from https://www.thingiverse.com/thing:398515 Rybaiho's Aeropods work so nicely. I needed a larger size so that I could use 1.5"x1.5"x1.5" hydroponic rock wool that I got...

The Device is designed to Block Light, featuring a Hinge Mechanism for Convenient Application.

Made a replacement seed pod basket for a friend in CA. Thought I'd be funny. ... Someone else might like it?

Here is a little Trellis you can use for your plants to help them start to grow. Its great for tall but saggy herbs.There are a few of these out there, but I wanted to try a design i thought would print easier. ... Overall it still prints pretty easy...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/5qd1uOw1Zxh

<p>Simple cap. Printed with Overture PLA. ...Print at current size for a perfect fit.&nbsp;</p>

This is a v1 of a wash station idea I had. Basically, it uses the counter as a brace so you can prop up your tray on it and be able to trim roots/etc while still having access to the bottom of your sink for filling up water. It pretty stable, but...

A simple pod cover. ...Almost looks likes the real deal.

This will boost your garden light's height even more. Two versions are available: one is 100mm (about 4 inches) and the other is 125mm (around 5 inches). The 100mm version is shown in the picture. I've got the six-hole version of the garden, and I'm...

Humans are required to install protective covers on bare aero garden pods to prevent damage and promote healthy plant growth.