adjustable ir mount 3d models

An (untested) remix for the [IR Probe](https://miscsolutions.wordpress.com/mini-height-sensor-board/)

Heavily modified version of the IR Probe Mount from realrenshai for his "Wanhao i3 V2.1 Titan Aero with BLTouch mount" Use this mount with his carriage plate remix! Link: https://www.thingiverse.com/thing:2271321 The original IR Mount didn't got low...

A remix for the camera housing to fit the MakerHawk IR fisheye camera (ASIN: B07DRH5Y5S). I also made a longer arm to get a wider overview of the buildplate. It requires: -4x M3x20 screws to assemble the camera housing. -1x M3x12 to...

Slight modification of Shenkoe's design (https://www.thingiverse.com/thing:4729272): - I added cut-outs on the back of the camera case for 14x14mm heat sinks (the IR leds are running quite hot otherwise) - The original corner mount is colliding with...

... or security networks. The IR capabilities of this system allow for clear and detailed footage even in low-light environments, making it an ideal choice for a wide range of applications, from home monitoring to commercial security installations.

This case opens up that third hole. If you print all three components, you can then print all of the arms and remaining brackets from kevinlo's design: https://www.thingiverse.com/thing:434600 The rear mount accepts a 4mm nut, the case closes with...

This custom design fits my model of the pi cam perfectly and allows it to breathe with its three photovoltaic sensors, one on each IR blaster and one on the main board. The third hole, previously blocked by the case, is now accessible. To complete...

... Furthermore, I added air holes to the back body of the camera to enhance cooling efficiency, as IR spots tend to get extremely warm during operation. This redesigned stand allows for a completely print-able camera without any supports required.

Firstly, the IR Mount on my E3D V6 hotend was causing unstable results, leading me to search for an alternative. The second issue was with my half-circular fan duct, which wasn't providing the airflow I needed. To address these problems, I...

An (untested) remix for the IR Probe Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Category: 3D Printer Parts

https://www.thingiverse.com/thing:3516771 If you plan to use this mount, be aware that with the original design, the camera would face either backwards or forwards instead of downwards towards the printer bed. ...I made some adjustments to the...

The monitor mount provided by MIKIADMS is to large, it block part of the screen below the mount. This mount is much smaller, it won't block the screen. The magnetic ball tripod head is also kept. How to assemble: 1. Disassemble the original...

Just my design of a Insta360 Go camera mount for the Diatone TinaWhoop. ...Super Simple.

This is a remix of Thing 2755175, utilizing the mount found in Thing 2477180.

This is my first remix. ... I liked the original model but wanted to have the option of a GoPro mount.

The mount snuggly fits over the X carriage at the screen end and the mount is tilted just enough for a clear view of the nozzle. This mount should in theory work with any Raspberry Pi Camera. IMPORTANT : You will require a longer camera cable...

Also incorporated Teaching Techs generic mount design, to be able to use cable ties, rubber bands or straps instead of screws to secure the camera to the mount. ... The holes for the nuts/screws in my design have a center to center distance of 20.8...

Attach the sticker to the center of the bullseye logo and adjust the infrared sensor's position, fine-tuning its height until you're satisfied with the results. ...Hold off on printing for now; we're not done perfecting the sensor's alignment.

... ... In order to optimize the design, I relocated the mounting piece on the rear section in an effort to create additional space. ...Furthermore, I have uploaded both the front and back components as separate entities for enhanced customization options.

I ended up ordering an IR camera that turned out to be too big for the original IR camera mount housing. So, I adapted this one to work with the swivel and arm of the original design. This is the IR camera I bought from Amazon.

I ended up ordering an IR camera that ended up being too large for the original IR camera mount casing. ...So I modified this one to work with the swivel and arm of the original design. This is the IR camera I purchased from Amazon....

https://www.prusaprinters.org/prints/21963-adjustable-ir-sensor-chimney-for-prusa-i3-mk3s-with-mm2 This is a remix of ad_lamy's great work, the Pass Through tool head and motor mount. His design has many improvements for the tool head on the...

The reading kept fluctuating between 0 and 1 and I consistently had load failures as it was a 50/50 if the sensor would read 0 or 1 at filament load. I modified the IR Sensor Holder for the MK3S+ (only MK3S+, the holder is different from regular...

The reading kept fluctuating between 0 and 1 and I consistently had load failures as it was a 50/50 if the sensor would read 0 or 1 at filament load. I modified the IR Sensor Holder for the MK3S+ (only MK3S+, the holder is different from regular...

This PiClop scanner version employs a Raspberry IR camera with an adjustable lens and a suitable shield to drive two red line lasers and a stepper motor. The Raspberry Pi 2 board and laser supply voltage (5Vdc) are derived from a stepdown DCDC...

https://www.thingiverse.com/thing:3467644 These mods are specific to the IR Sensor mount also known as the Chimney. This mod uses a small metal spring to push against the Motor mount. All you have to do to adjust, tune or calibrate the IR sensor is...

... "Tablet Base Strong" available if you prefer extra strength. Print one of these "base" parts along with a "Tablet Holder" and a "Tablet," then use M3 screws to assemble them together, allowing for adjustable direction through their screw-in design.

Original Wall mount did not quite fit, couldn't screw all the way down

This is remixed from the "unvented back" from https://www.thingiverse.com/thing:3728526 I just changed the size and shape of the bracket used to mount the camera case so it can be used with this mount -> https://www.thingiverse.com/thing:2886101 I...

This is a custom IR probe mount designed by David Crocker, also known as DC42, specifically for use with the updated E3D v6 featuring a smaller heater block and silicone socks. I was searching online for this design when I encountered several...