adeptus mechanicus models

 This model is currently a working draft. Solar astronomy has inherent dangers, please be sure you understand these (see also below). Use is at own risk. More general information about this approach to solar astronomy can be found at the Sol'Ex...

Manufacturers known to make perfect fans do not have a 30mm model, they start at 40mm.The 30mm one I got off of Amazon is crap and I had no idea which ones are good since they are all made by unknown brands.So I decided that I wanted to use a 40mm...

Printing time is &gt;15min.Credits:The original configurable OpenSCAD model is by wstein, posted here. ...Thank you Werner!</p><p>Thanks to <a href="https://www.printables.com/social/78665-darktiger/about">darktiger </a>for his print and picture of the...

The "cylinder" rotates, and will index to set the drill guide sizes for any of the 6 holes. This version has a "cylinder" which is designed with holes that are 2mm, 3.6mm, 4.4mm, 5.2mm, 6.0mm and 6.8mm (which correspond to 5/64, 9/64, 11/64, 13/64,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Printing Recommended slicer settings: Resolution: 0.1mm - 0.2mm Infill: 10% - 20% Supports: Doesn't Matter Rafts: Doesn't Matter License The "Customizable Arduino Nano LED Candle (2 - 6 LEDs)" model (.stl) is licensed under the CC BY license by Code...

If the format you use is not yet in the downloads, let me know, I will create the models for it. Now print the test part (#0 testmodel) start with the smallest tollerance and try to push the test part over the profile, it should not go strongly...

The stock globe has a vent on the top and there are vents in the model to aid the convection cooling. Is it *really* needed, especially with the converter gone? Dunno so the optional rain cap comes with the caveat of possibly shortening diode...

... recast into a new weapon. By Alex Wellerstein, a historian of science and an assistant professor at the Stevens Institute of Technology, in New Jersey. Attributions: -Screwdriver by user DAPE (under CC-By-Sa-Nc). -Demon Core modeled by Szadros.

On homemade springs using generic musical wire When it comes to homemade magazines, the models by Thanhtacles are designed to use drum springs unlike the box springs exemplified by their commercial counterparts, for what I assume is the most...

Models intended to be part of the numbers node all begin with the prefix MMU.Card Compression Spring: if you have problems with the card compression spring lifting off from the bed, it is recommended you add a skirt of at least 6mm.Assembly...

They aren't really required - they just provide some more protection. In addition to the printed parts, you will need the following: 1) 1/4-20 threaded rod, 3" length 2) 2 1/4-20 nuts 3) 2 M6-1.0 hex bolts 16mm length 4) 2 M6-1.0 hex bolts 30mm...

...I propose some activities to do programming this robot: First goal: Making it move The first and basic activity could be to program and model their movement, to find the correct position sequence for each leg for a forward run. First step: assembly.

IntroductionMany designs like RC cars and trucks, lanterns, model houses, etc. would benefit if 3D printing could be used to create truly transparent window panes. But as you might know, FDM printing transparent filament per se does not result in...

... one at a time by clicking Download each time. Or click Download once on the file Girl_Unicorn.rar ### My some other things: Category: 2D Art

Both the original base (Base.stl) and the updated version (Base_Rev.B.stl) are included. 4 (7/15/18): Added versions of the Deer Scarer, Waterfall, and Electronic box with custom supports modeled in. Supports were built based on the method showed by...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the "tap and knock off" method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.8. 0-10V...

I suggest printing samples of just the top 20mm of each model to make sure they fit before printing the whole tower. 3rd UPDATE: I've added a calibration print. This is a small sample of how the two halves of the v2.5 towers fit together. You can use...

As this is a rather large model it will take a buildplate of 212mm by 175 mm, so this will not fit on a smaller printer's buildplate, but it will fit fine on an Ender 3 and similar printers. My goal was to create a phone holder you can trust with...

The 3D printing process sometimes leaves whiskers or small blobs of plastic which might jam the fully assembled power train unless each stage is run-in until all parts are worn smooth when the whole will operate as designed.&nbsp; &nbsp;Assembly:1)...

In the end I think the best way is to simply open up the 3D-model of the whole maze and just put obstacles together one by one. Therefore I Added a few different files (STEP, STL, 3D-PDF (<a...

But if you are not confused by the small size, you can also print them on a 3D printer. To increase the size, you can cut these models into pieces, print them separately and then connect them with glue. Download the files you need one at a time by...

Real quick: Check out my other S22 designs like my LED handle/boomerangs, help me spread my design by hitting the like button, post a photo as a make once you've printed things out!! There's an active community on this, come:</p><ul><li>join the <a...

Learn everything about the V-Core 3 on the dedicated project page: v-core.ratrig.com. External links: Buy Kit at Rat Rig Step by step Build Manual Facebook Rat Rig 3D Printer Community Project Page (BOM, Build Guide, Files, Electronics, Firmware)...

The use of simple metal parts in combination with printed components holds a lot of potential for the future; FreeMenDontAsk is already working on other handgun models. Even outside of gun making, this could be useful for a wide array of printed...

But if you are not confused by the small size, you can also print them on a 3D printer. To increase the size, you can cut these models into pieces, print them separately and then connect them with glue. Download the files you need one at a time by...

We are modelling the *BELT* tooth here, not the tooth on the pulley. Increasing the number will *decrease* the pulley tooth size. Increasing the tooth width will also scale proportionately the tooth depth, to maintain the shape of the tooth, and...

Have a close look at the photos and assembled model (wall_clock_07.stl).PlatesThe bearings are hard to push into place, this is where the bench clamp comes in useful to push them flush into the plates.The front plate needs a 30mm M3 screw to hold the...

# Reddit Post For anyone who want to try this themselves, I created my own "Cloud Streaming Console" by taking a few components I had, modded the plastic on a Gamesir X2 Pro controller, modeled and 3D printed a basic "shell" with some handles and...

Or rather, it's a scale model of what that house looked like fifteen or twenty years ago. The wrecked version is closer to how it looks now that it's been abandoned for the better part of two decades. The tweakers have had a field day with this...