add laser to ender 3 3d models

I found @mariodab's laser mount blocked the X limit switch on my Ender 3, so this makes it a tiny bit slimmer and gives some more clearance for the laser mounting screws at the front. ... To prevent blocking access to the gantry mounting screws, I also...

A bracket to mount the original Creality Ender 3 laser kit onto the Ender 3 v2 print head.This design does not require any additional screws, very simple design. ...You can print it without using any support, the hook is very small an should print...

Todo: * Fix the temperature table of the laser (I'm struggling to find one for Neje laser) * Disable heated bed option * Remove Bed temperature from status screen * Extend Z to make laser focusable via Z stepper * Add smoke extractor * Add a cable...

In order to covert my Ender 3 Pro from straight 3d printing to Laser Engraving, I purchased the Creality 1.5 mw laser attachment. Once I received it, I realized that I wanted to make a permanent conversion rather than just utilizing the magnets...

Converts the hotend for an old, broken ender 3 to accept the sliding part on higher power neje laser modules (30w, 40w), converting it to a laser engraver/cutter that can be used with lightburn without any other modifications. Uses fan pwm to...

To build this incredible setup, you'll need the following materials: * Two M3 x6mm screws to secure the laser module in place * Four 25x10x3 magnets that will powerfully hold the laser mount in position * Two plastic screws designed specifically for...

This is a cutting-edge laser and auto bed leveling sensor, the SN04-N, specifically designed for use with the Ender-3. It's also engineered to work seamlessly with the CR-10 Fang 40x40x20mm Fan Cooler, as featured on Thingiverse in project #2683629.

This was an effort to eliminate tooling changes between printing and etching on the Ender 3 Pro. This setup creates a screw on mount in place of the provided magnets for attachment. Once completed, this allows you to switch from laser to extruder by...

There are two models a straight (which should fit most Ender 3 V2s) and one which has the laser end tilted 2.5 degrees as it seems my fan cover does not sit level and this compensated for it. ... This is my first model, might be a little over the...

... your nozzle, and then reinsert the middle screws. Regularly check these fastenings, as they may become loose over time due to vibration - a concern applicable to all bot's hardware components. ...Wishing you success and good luck in your endeavors!

This is a laser mount that clamps onto the Ender 3 V2 stock head case. You can use it either with the stock Bowden or right-handed Direct extruder. ... https://www.thingiverse.com/thing:5673876

9mm Croshair laser fixture that can be mounted using the 4 screws from the Fan of a 500 mW original Ender 3 carving Laser. Focus height of laser must be : Z 86 then crosshair and carving laser line up. ... This crosshair laser gives you always a correct...

I wanted a rotating laser turret on my Ender-3 Pro so I combined these two things. https://www.thingiverse.com/thing:2292057 https://www.thingiverse.com/thing:3544547 I also included the STL file for the measuring tool from the extruder knob...

Laser holder for 16mm lasers. ...Made for Ender 3/Ender 5/Ender 5 Pro.

Ender 3 Bottom Fan Cover - Laser Cut Alternative Feeling left out? Not the laser! It's now teaming up with your 3D printer, saving a ton of print time and keeping plastic debris from clogging your fan. This upgrade is quick and easy to install. The...

For this project I needed a way to attatch a honeycomb laser-bed to the print-bed of the Ender 3. I have therefore designed these little clips, that securely fasten and distance the honeycomb bed using M4 screws from the bottom. You will need...

Head mount bracket for ender 3 v2

Long range plans will include a stopper to keep the z height locked at correct height as well as a safety switch that will cut power to the laser if door is opened. Laser light is nothing to play with, and safety is a top priority with them. Do not...

This gcode file laser etches a test using laser power from 10% to 100% to test material etching. ... I wrote and used this with my CV 1.6w laser but will work with larger powered lasers.

Adapterplatte zur optionalen Montage des Lasers an den Montagepunkten des Sprite-Druckkopf. ... Adapter to mount the laser at the same points as the printhead.

Created specifically for the Geetech A10 to operate the Ender 3 hotends effectively.

Support pour laser

... and did not like the Magnet mount alone. Designed this to catch on the Extruder cover so the laser would be just about center to the extruder. ... Please ensure that when enabling the Supports that you set it for Touching Base and not everywhere.

I purchased a 1.6W UV laser from China, seeking a quick and easy way to attach and detach it from my printer. I chose to secure it with magnets and a custom bracket that fits snugly on the side of the hotend enclosure. To tap into the part cooling...

For some reason, the .stl is saving with the part on its back, so I would recommend rotating it to sit with the laser exit hole down. That was how it was designed to be printed. To install the mount, you do need to remove the lower two magnets...

I used a nail as the flag trigger in bfptouch that was longer so the other holders were shorter for my setup, thus causing the bfptouch to scratch my print bed, so I designed a holder for bfptouch and laser (8W) that I have. The laser has an outer...

Created for CREALITY12V/24V High-Power Laser Engraving Laser Head Module. "4 Magnets were included in the shipment." This file includes 4 .STL files. All part can be connected: by a 3M - 8mm screw or glue. ... UPDATE: *Added new plate for BLTOUCH...

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

Members are welcoming to share result, ask questions related, and remix the files Ender 3 based to corexy conversion objective to repurpose of everything in ender 3 from screw to electronic. It also objective to be build by only used precut 2020...

I found that the round connector bars on part 2 were too tight to fit into part 1, because they were too close to the objects body. As such you could put them together with some force, but they would not come apart again.. ever.. LOL So I...