adafruit motor hat 3d models

This is a box for the Adafruit Micro-LiPo battery charger. ... There is a hole for the JST and USB connectors.Lid is snap fit and should hold the board down to the box. Print SettingsPrinter: Ender 3 Pro w/ direct driveRafts: NoSupports: NoResolution:...

A din rail mount for an Adafruit Cricket.You will need to print one tabs for this design.It can be found at: https://www.thingiverse.com/thing:3401942 orhttps://www.prusaprinters.org/prints/8512-din-rail-mounting-tabCategory: Electronics

Replacing the Pi Mounting Plate in the Adafruit IoT Printer Kit Upgrade to a fresh mounting plate tailored specifically for your Raspberry Pi Zero, complete with screw holes that ensure a secure fit. Choose from plates designed to accommodate M2.5 or...

I needed a mount for the Adafruit 16-Channel 12-bit PWM/Servo Driver Board used in this fantastic set at astromech.net: https://astromech.net/forums/showthread.php?33317-Flthy-s-Holoprojector-LED-Servo-System-Regulator-BC-Approved-100-(9-17)-Open. I...

This small enclosure is designed specifically for the Adafruit Si7021 temperature and humidity sensor. It features an 8 mm hole, perfect for passing cables through, allowing the user to mount it on a flat surface. ...The tube itself serves as a mounting...

Inside the case, you'll find an Adafruit PowerBoost Charger that allows me to run the RetroPie on battery power using a 6600 mAh Lithium-Ion Battery Pack. Additionally, there's a port in the back where I can plug in a Raspberry Pi and charge it from...

This enclosure is designed specifically for the Adafruit USB Micro-B Breakout Board. Currently, this enclosure is intended only for direct soldering scenarios; therefore, you cannot use the included header. The cable holes are specifically designed...

Key Features: * 8-channel I2C multiplexer * Selectable channel addresses for easy configuration * High-speed switching with low latency * Compatible with microcontrollers and other ICs that have an I2C interface The Adafruit TCA9548A is a useful...

It has been tested with https://www.adafruit.com/product/2993 but should also work with https://www.adafruit.com/product/2994.Assembly notesThe tripod mount is designed to work with a threaded insert and is currently sized as a clearance fit to allow...

Pimoroni Lens: https://shop.pimoroni.com/products/microscope-lens-0-12-1-8x?variant=31885093371987 (UK) Adafruit LED Ring: https://www.adafruit.com/product/5137...

Pimoroni Lens: https://shop.pimoroni.com/products/microscope-lens-0-12-1-8x?variant=31885093371987 (UK) Adafruit LED Ring: https://www.adafruit.com/product/5137...

To ensure flexibility and customization, the Adafruit Fusion 360 design incorporated user parameters that enabled easy adjustments to key dimensions such as width and height. However, during the redesign process, an error occurred when reducing the...

This is a quick-and-dirty enclosure for an Adafruit Clue with attached Bonzai Buckaroo. I designed it to have access to the Bonzai's alligator clip pads, access to the pump driver terminals, and the screen and buttons on the Clue. The Top is...

Four minor updates transform the Extended Raspberry Pi + Adafruit LCD Case: Expanded USB port simplifies cable connections, positioned conveniently on the bottom half. Reinforced standoffs now support screw mounts for RPi Model B, also located on the...

***Technical Notes:*** - The targeted Adafruit board features M2/M2.5 holes (measuring approximately 2.9mm). - Suction cups measuring 20mm work effectively, but larger sizes are also suitable. - For the benefit of self-tappers, we've included a...

Designed a minimal display stand based of adafruit's own stand legs however there were none available for the 3mm pitch display so I made my own. The angle is 65°. Can barely see the legs when viewing from the front and give the display a nice...

# Description Very rough model of the Adafruit 16x2 LCD Pi Plate serves as a useful subtraction for creating cases for the LCD panel. Useful reference: See the Servotester, an example available on Thingiverse at...

A rechargeable battery holder designed for Adafruit's Cylindrical Li-Ion Batteries, available in 2200mAh, 4400mAh, or 6600mAh capacities. The Holder with Cutout Capacity.stl file features a cutout specifically for the end of the battery where the...

This features an Adafruit 1/2 sized (or full sized if you're okay with it sticking out) Perma-Proto Breadboard alongside an Arduino Uno, Leonardo, or similarly sized board. The design has been slightly modified from the images in that the hole...

This is a mounting fixture for Adafruit Neopixel stick LED lights. Either the RGB version or the RGBW version will fit perfectly in the fixture. It's designed to slide onto the edge of a PCB that's at least 1mm thick, providing a secure hold. For a...

Simple case the Adafruit's Bluefruit LE Sniffer comes with two different lids, one featuring "BLE Sniffer" lettering and a plain version. Four 2-56 x 1/4" or 3/8" machine screws are used to hold the case together securely. The board fits snugly in...

I was designing a mount for the macropad to use on my Fanatec steering wheel and isolated this piece of the original Adafruit stand to save myself some time. ...Rounded the corners on the bottom end of the frame to match the original top for...

I attempted to print the original NeoPixel Coat Buttons from adafruit. Unfortunately, with a 0.4mm nozzle, they came out too thin and fragile. To overcome this challenge, I decided to simplify the original design and make it easier to print. The...

A stand that supports the Raspberry Pi in the custom case with an Adafruit PiTFT screen is designed to position the device at a 60-degree angle for comfortable viewing of the screen. The stand comprises three printable parts requiring gluing. In this...

A custom base for the Adafruit "UNIVERSAL QI WIRELESS CHARGING TRANSMITTER" is designed. It can be printed with either low or high resolution, accommodating the charger in both cases. An open hole allows the charging plate to be placed on top,...

... a feature for adding an external reset button. I employed a button like this one: https://www.adafruit.com/products/1119 Print Settings: Printer Brand: Monoprice Printer: Monoprice Select Mini V2 Rafts: No Supports: Yes Resolution: .1mm Infill: 25%

(I also used the JST connector from his Adafruit Micro Lipo MicroUSB model) Thanks for the great models that saved me a ton of time!!This model is part of a redesign of the base for my DIY LED Bubble Tube...

I'm creating a simple stand for my Pi 3B, drawing inspiration from Adafruit's sleek and minimalist Raspberry Pi Zero stand. The design is a rough first attempt, but it works surprisingly well - the base could even be smaller. Two-millimeter standoffs...

Two part part press fit design for mounting a [strand of Adafruit NeoPixel LED](https://www.adafruit.com/product/3630) to a sheet of 2.7mm cardboard. * Cut an approximately 18 mm round hole in the cardboard * Out one of the pixels through the hole ...

They can be found at: https://www.thingiverse.com/thing:3401942 See the entire collection For Adafruit Stand alone: https://www.thingiverse.com/thing:4831968 Din Rail : https://www.thingiverse.com/thing:4833199 For SparkFun Stand...