ad410 amcrest 3d models

This is a 30° angle mounting wedge for the AD410. I couldn't find one anywhere online so I made my own. I think the angle is actually slightly under 30°, but it's very close and works well enough that I don't have much interest in fixing the minor...

I created a cover for my Amcrest Ad410 doorbell to make it harder to steal. ... It is made for 15 degree mount, and I think it can be mirrored to face the other side if needed.

Here is a Amcrest ad410 Video Doorbell 45 Degree(Left) Mount. ...I found other mounts but only for the Amcrest ad110.Print with PETG and 50% infill.Enjoy! 

My 1st 3d model is for an Amcrest ad410 Video Doorbell 45 Degree(Left) Mount. I found a couple mounts for the ad110 and other doorbells but none for the ad410. I looked at a couple designs by Garps for ideas then took my caliper to my doorbell and...

Loved the secure case alexeyzel made for the Amcrest AD-410. Works great when you attach the factory angled mount behind it. ...But I have siding, so I added a standoff for 4" siding.

I wanted solid so done 90% infill, but less probably is good too. ...I printed with petg. Amcrest included wedge and corner brackets were not good enough. ...So I did 2 in 1 with 37° corner and 5° tilt down.

I called Amcrest technical support to inquire if they had a 5 degree tilt down adapter with combination use with the Corner Angle supplied adapter. Since, both adapters inside the AD410 box cannot be used together. Unfortunately no adapter...

I wanted a small 35 degree wedge mount for my AD410, but Amcrest does not sell those. There not a lot of options for the AD410, but not for the AD410. This mount uses the standard doorbell distance mounting holes of 50mm, similar to the Nest...

A 20° wall-mount for the Amcrest ad110

Made a tall junction box for Amcrest Cameras. ...Great for lowering camera mounted under soffit.

Simple bracket to mount an Amcrest ASH21 camera to a wall upside down.

Mount for Amcrest dome cameras, such as IP2M-851, conceals wiring bundles. ...Secure the camera using 6-32 3/4" hardware. Source: https://github.com/swilson/freecad/tree/master/amcrest_dome_camera_mount

Amcrest WebCam Lens Cover. ...Allows you to obscure the camera lens when you're not actively using it.

I bought a refurb Amcrest AD110 Doorbell and it was missing the wallplate. ...This is a replacement.

Amcrest AD110 doorbell wedge; remixed with: - nuts for doorbell bracket - larger mounting holes - additional space for bracket

This is a mount bracket to be used with an Amcrest IP8M-T2499EW and IP8M-T2499EBor others with the same style but maybe a different lens. ...

The original Amcrest package comes with only one fan and one bracket, but you can now easily install two quieter fans to replace the loud stock unit. ...To do this, look for a 10mm wide fan that fits on one side - it's the only one that will fit in this...

A customer commissioned me to figure out a way to mount these cameras to a pole outside. ...This is what I came up with. Use a hose clamp and 3 screws to mount the Amcrest IP2M-852EB to a pipe. ...Print in PETG or ABS for outdoors.

Corner mount for Amcrest IPM-HX1W and IPM-HX2W or similar IP cameras. ...The metal bracket that comes with the camera screws directly into the base and attaches securely to the wall via a single spot on each side utilizing 2-sided tape, preferably a 3mm...

These mounts are specifically designed for Amcrest's dome camera, offering versatility with two separate options: one for installation in a corner and another for secure placement on a rain gutter. ...The design of the corner mount features a hole that...

This was designed and printed so that my Amcrest ProHD PTZ camera could look out a 2nd story window and look down enough to see everything. ...I uploaded two versions one has roughly a 17degree pitch (CameraShim_17d.STL) the other I think was roughly...

A customizable wedge for the amcrest video doorbell (ad110), it defaults to right-side mount. The wall mount screws default to a standard doorbell with 55mm spaced screws. ... y_angle controls vertical tilt, x_angle controls horizontal tilt, flip...

These are mounts for Amcrest's dome camera. One for mounting in a corner and one for mounting on a rain gutter. ...The hole in the corner mount is for the cable to pass through so the camera can be mounted over the wall where the cable passes...

I made this basic stand to hold my Amcrest Indoor WiFi Camera to point out my window above the point that the camera view would be blocked by the window frame, It is a very basic design but works and fits the camera well. Print top side down so...

This is an adapter to enlarge the locking knobs on an Amcrest microscope to make it easier to get enough force to lock the adjustments for those with weaker hands. It slips onto the existing knob and can be held in place with a small blob of silicone...

This is an adapter designed to amplify the locking knobs on an Amcrest microscope, making it simpler for individuals with weaker hands to apply sufficient force to secure the adjustments. The adapter seamlessly fits onto the existing knob and can be...

Amcrest AMCPFA136 Junction Box for Dome Cameras, Should be compatible with the following armrest model cameras IP3M-956B/W, IP3M-956EB/W, IP4M-1028B/W, IP4M-1028EB/W, IP5M-1176EB/W, IP8M-2493EB/W, IP8M-2493EW-V2, IP8M-2496EW-AI The B/W at the end is...

However, the specs in the Amcrest docs for this camera are obviously incorrect. I found a picture of a similar camera and dimensions that I used and that's why the box ended up to be smaller. Screw holes fit 4mm x 5mm screws and they self thread...

Base box to hide cords and mount Amcrest Security Camera (ASH43)

This is a mounting plate adapter for an Amcrest 2493EW camera that allows you to mount it on a structure built for LTS CMIP7223 camera