action figure 3d printing files

Using TMC2130 drivers ([plus my other modifications](https://www.thingiverse.com/glabifrons/collections/glabifronss-anycubic-kossel-mods)) with this hotend and Klipper firmware, I was able to print 400mm/s with fairly nice results (very minimal...

I highly recommend printing these with PETG rather than with PLA. Also, the magnets can be difficult to insert. Use a flat thick metal tool placed over the magnet while pressing down with your thumb. It's designed to be a snug fit so that superglue...

I switched materials and I am now convinced that the print quality is actually quite a bit better over the original gantry. Update 2020-04-04: Made a v4. Changes from v3: * Added cable management rings to all the mounts * Added BLTouch versions of...

To complete it, you will require the following items: Alligator Clamps: 6 - https://www.amazon.com/gp/product/B008IEFHRQ/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1 Flexible Hose: 6 -...

keep additional ons as you see fit for the meter, USB etc - do the same for the live for any separate circuits you may add - create a harness for the banana plugs, and anything else you can before you start assembly - I suggest adding at least...

Since all parts are printed, it is still possible to "upgrade" here if this connection is not stable enough. Future extensions: Installation of a recess for a switch if necessary, installation of a speed control (potentiometer) Installation of LED...

Then print it out together with a T-piece. Glue it together in the slicer, so to speak. That's how I did it with the glasses box, or with the mini-Jo ;-), both of which are not mine, I just put on the T-piece. And I also had to think about...

The box and face are printed in PLA with a color change for the digits. There is also an aligning part to glue (super glue) the face frame to the face. Also included is an LED removal tool – so you can support the back side to tap a failed Led...

Below is a guide with very simplified photos in Italian and English versions, and at the end of the article the settings used in print (at least for me.) Good reading. Hoping to have done something pleasant for the community, thank you very much,...

Do not glue the skewers into the holes; even if the printed part literally just falls off the skewer, winding the thread onto it will keep it all securely together. ...Not gluing the skewers in will also let you remove the skein label and reuse the...

I have tested it on Bosch wiper blades, but others are sized similarly so the tool should work on any of them.To use, clean up your print first. Any sort of stringing or spikes in the guide slot might affect your result. Also pay particular attention...

It is the low-poly and easy to print version of ionic, doric and corinthian columns. Doric and corinthian columns are supportless, only ionic column has some easy to clean supports. Just like chess knight is not photorealistic and just symbolic, goal...

Print them as I have shown in Cura, with or without supports. The vertical holes will be fine; it's the very hole on the bottom that gets stringy, but it still works. I was going to add a small cylinder in Fusion and make a pre-modeled support but...

ive not printed these yet to try them but they should be the same as the ones im using now just being round instead of square. thought id update this with them incase someone who wants to try this would rather have the round instead of the square. ...

**Example Python Code Using These Parameters:** ```python import math # Sample Function: def generate_branch(shape_id, current_x=0.0): print(f"Generated branch at X: {current_x} ShapeID={shape_id}") class BranchTreeGenerator: def __init__(self,...

Simple and effective, sure, but I saw the opportunity to print something to make it all more compact and bring all the key pieces together. I purchased the [Longacre basic...

... Carl XVI Gustaf of Sweden presented Pink Floyd with the Polar Music Prize for their contribution to modern music. Thanks for checking in on us and for your ongoing support.CR8ED Out Of Hand Sculptor - Sandy Campbell3D Scanning and Printing - CR83D

Shake it again and it's a one minute timer! A demo and step-by-step building instructions is available here: https://youtu.be/lHQFzX9xagM The brads system can be used for any other project without having to sacrifice a Micro:bit board. This project...

**Serial Communication**: The code includes Serial.print() statements, indicating that it's designed to communicate over a serial interface, likely with a computer or another microcontroller. 3. **Timing and Loops**: The code uses the `millis()`...

I suggest printing the top pieces in something more heat resistant than just PLA, preferably carbon fiber nylon or polycarbonate. ASA should work pretty well too. For the bottom pieces, I used PETG as it allowed for the cards to slide in and out...

I would make the cable length to reach from your pants pocket to your goggles, or your shirt pocket, whichever works for you better. PS: If the LiPo buzzer is too loud stick two pieces of bubble gum into holes of little speakers, that will make the...

Before that, we chop off one point of each curve, otherwise we will end up with double vertices at the seam, which irritates our slicer software when printing. This is our result after the UV Connection node. The mesh looks good, but the top and...

... structure (https://www.thingiverse.com/thing:4695870). So I also redesigned the 140mm spindle. It now has a hole at the top where you can put a (colored) steel ball. Also, the bottom edge is rounded to make printing the bottom a little easier.

It may be a cap or expansion space.C1 - A cap with a solid top.C2 - A cap with an opening sized for a voltage display.C3 - An expansion space to accomodate a device up to 80mm x 50mm x 17Dn - A cap for a C3 componentD1 - Solid capD2 - Cap with...

... Some part coolers like the "Petsfang" & "Bullseye" seem to crash into the camera housing during autobed leveling. Many thanks to "acwest" for pointing out that problem and his solution! ===================================== Have fun printing!

When I printed it, I placed the A blocks right next to the B blocks in the slicer, so they were already joined together. Here are the coordinates in case you want to get neighboring pieces, or need them for whatever reason. I'm also including...

Designing and drawing this model required over 1200 hours of work, and printing it took an estimated 2000 hours. The model uses various colors in PLA, including True Red (10 pounds), True Yellow (2 pounds), True White (8 pounds), True Black (4...

There is the possibility of ordering FRONT PLATE in .dwg to cut in CNC MAGNETIC PADDLE SHIFTER are included PARTS REQUIRED: M5x5 Brass Inserts (4) https://es.aliexpress.com/item/32958273559.html?spm=a2g0s.9042311.0.0.274263c0jpEjAL to screw front...

**Instructions** - Print one copy of the Piédestal and of the Cercle cranté (that's pedestal and notched circle for you english speaking people) and six copies of the Secteurs (sectors). I advise to join the sectors by twos (a simple adhesive is...

In the meantime I have developed this holder for 30x 1 Euro pieces so that you can just put the whole thing in the glove compartment and the coins do not roll wildly through the area.The distance of the coins is minimal from each other and the...