action figure 3d printing files

After puting up with a leaky milk pourer until it fell apart and after finding replacements were expensive and just-as-poor-quality as my old one, I decided to print my own, in just 3 parts (plus a store-bought o-ring): * Body/Bottle * Screw-top *...

Print 2 of each half-wheel and use clamps or a hammer and a wood block or press/drill press to seat the bearings in place. Next, place one pair of the half-wheels around the tire, using bolts to align the holes. Use clamps to hold the two halves...

The print time for this project is around 13-15 hours with a layer height of .28. https://youtu.be/-cRUheSAXM4 [Update 2] After finishing my assemblies and using them, I can confirm that the coupler I made is strong enough to handle the cleaning...

... of the column. ‘Greetings,’ said the pale Blood Angel. His portcullis-faced Mark III helm was under his arm, leaving his face bare.” He doesn't have a bolter because I already had a Heresy-era bolter to use that I attached to the printed model.

Print the board and 16 pieces. Cults will not allow me to upload the rules document so I will paste bellow. Object of the Game Be the first player to move all four of your colored pegs around the game board and into your FINISH line. During the...

Install Klipper and make use of your Pi's processing power to speed up and improve your prints. There is a [good guide on reddit](https://www.reddit.com/r/klippers/comments/kj2h5r/stepbystep_guide_for_ender_3_v2_klipper_w_bltouch/) for setting this...

From strength and flexibility, PETG seems suitable as the print material. While PLA can also be used, it is hard and brittle, so it may break easily or cause problems with the fit of the nose frame. Initially, I thought of attaching paper to the...

The case is designed to be printed with a layer height of 0.2 or 0.3mm. You can lower the height if you want more details which is recommended for the ARC reactor. Supports are needed on some parts.I used PLA on everything but the electrics carrier....

[Wemos D1 Mini](https://www.amazon.com/IZOKEE-NodeMcu-Internet-Development-Compatible/dp/B076F52NQD) or [NodeMCU](https://www.amazon.com/HiLetgo-Internet-Development-Wireless-Micropython/dp/B010N1SPRK) * Get a USB charger for at least 5V 2A To...

This is my first attempt at sharing a 3-D printing model. History: A few years ago, after purchasing a CNC machine, I decided I would design a D-Handle that I could use for my Porter-Cable model 450 compact/trim router. I believe I came up ...

A complete unit requires 1x Post (Lower), 1x Post (Upper), 2x Sleeves, 2x Through bolts, 2x Bearing Cups, 3x Arm (Hole), 3x Arm (Peg), 3x Arm Clips, 3x Brackets, 3x Rods, and 6x Hands to be printed, with 2x 608 bearings. Optionally included is an...

Both had errors that prevents them from printing properly. ... ________________________ <b>If you like my work please consider supporting me on Patreon.</b> <a href="https://www.patreon.com/bePatron?u=30583762"...

Print all 3 sizes of each part. 2. Sand the barrel and rail supports wherever they will make contact with the barrel shroud, tank, and scope rail. I used 600 grit. Wipe the parts clean. 3. Install the shortest rail support. It should require...

After numerous requests, I also included the Z-probe for the Bl-touch in the gallery photos.Below is a guide with very simplified photos in Italian and English versions, and at the end of the article the settings used in print (at least for me.) Good...

The bottom has been printed, and it works. My bolt holes were a tad loose, but that was all. I have since decided to move on to a rear-mounted box as seen in a recent Teaching Tech video. (06/11/2019) There was an issue with the 1x10 dupont slot on...

To build, just print two ears, then attach the 450mm lengths to the tabs on the ears with t-slot nuts. It should be pretty self explanatory. m3x5 screws should do the trick, but if your parts shrink too much a washer may be useful to ensure a tight...

FR Tournevis compact avec chargeur 8 têtes à rétention magnétique. 1 aimant cylindrique de 1 cm x 1 cm est indispensable pour le fonctionnement du stockage intégré au manche l"aimant est en contacte avec la base de la lame porte tête ce qui permet...

https://www.amazon.de/dp/B07YSV66Y5/ref=emc_b_5_t?th=1)8x Socket head screw M4x12mm4x Countersunk screw 3x25mm16x Washer for M58x Socket head screw M5x20mm8x Nut M5Silicone or any other sealant to tighten the sealing surfacesMy airtight dust...

My huge thanks to both of them. Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2**Rafts:** Yes Supports: Yes**Resolution:** 0.2 mm Infill: 20% **Filament:** [ Makerbot PLA...

This is a Custom-Made Starter Box for the 22RE Toyota Engine https://www.thingiverse.com/thing:644933 My completed project can be viewed at https://www.thingiverse.com/make:692499 # Print Settings 1 x StarterBody1 : Layer:0.15mm Raft:no Support:no...

to the picture).4) Zip-tie, screw or stick (doublesided tape) the gimbal controller to your plate.be careful that the m2 screw in the middle of the plate doesn't short out the controller!5) If you want print out this nice cover:...

You'll need to print three of my custom-made carriage blocks and three 10mm spacers. Don't use the blue carriage plate, as my new carriage block is integrated into it. Follow Shaunppl's instructions for installing linear rails on extrusions. His...

Every glance at this work of art will make your eyes light up with admiration.Printed in PLA or PETG, the robust material ensures long-lasting stability, giving your board a firm hold while creating a harmonious connection between window and...

(ALL OF THE ABOVE ICONS ARE ALSO SOLD SEPARATELY ON MY PROFILE.) (MIRROR THE ICONS FOR USE ON THE RIGHT SHOULDER PLATE SO THE ICON IS FACING FORWARDS AS INTENDED, THIS CAN BE DONE EASILY IN ALL SLICERS) These models are designed to be fitted atop...

In it's current state, however, I do find the wallet quite usable.  Assembly:Print a base, lever, cash compartment, and then lid. Add magnets to the holes, being extremely careful to place them in the correct way, so that the ones in the lid actually...

For most standard nozzle 0,4mm the details are too small.Assembly:After printing, the dipstick and axle are inserted into the body.Then put the scale over the axis on the body, the moving parts can be "greased" with some liquid soap and a little...

You only need to print one lid for an entire stack. The idea is that you simply pull out the component boxes, unstack and remove the lids and the components are ready to go, in bowls, so your components are neat on the table. The magnets are placed...

All necessary parts for a compact, three-dimensional printed mini tri copter modelled after RCExplorer V3 will need to be acquired. This endeavor relies heavily on David Windeståls impressive design and accomplishments. Those wishing to assist David...

Every part is designed to be printed without supports. All the electronics and extras I used are listed below. I had to scale the parts up by 2540% in the slicer. 2x Boss 4" Speaker Driver...

You can also refer to this video from Embrace Making for dissasembly assistance, it helped me so much when I was trying to do this I've tested it on all-metal version with dual-fan setup, you can refer to my klipper config if you need to (Please...