action figure 3d printing files

Even at 100% infill, it uses only 0.34g of filament and the print is only about 4 minutes long because the part is so small. When installing the restrictor clip, the recommended procedure was to take the door off leaving the hinge attached to the...

Recommended to print with the ears pointing straight up with supports, so the taper along it's surface doesn't get messed up by the support material (unless you're patient enough to sand it and do some cleanup. I am not.) Support material will be...

This quad suffers from the same issues as other similar designs: The printed parts are not robust enough and will likely crack due to vibrations. After some time, the part will resemble shattered security glass with numerous cracks. To assemble this...

As above, it'll work with the old version too, so if you only want to make your speaker louder, you can just print this side and replace the equivalent part on your existing thread alarm. ORIGINAL POST: I wanted a little filament alarm,...

Here's a summarized version of the guide: **Step 1: Prepare Adapter Base** * Remove the existing hotend and any debris * Install a new M3x10 screw into the adapter base * Use this screw as a reference for future installations **Step 2: Install...

SETTINGS: - material = PLA - layer height = 0.16 mm - infill = 15% - no support - print speed = 50-60 mm / s  PARTS: -TAB 1 = 73 g - change filament to another color at 57% -TAB 2 = 72 g - filament change of another color at 53% -plane = 3 g -...

... those looking to boost performance even further. Please note that these parts are not for commercial sale in any form. edit: I've uploaded the 16mm version. edit 2: The 9/16 holder has been updated to reflect printing tolerances. ... Cheers, Harun

Pros • Direct drive conversion • BLtouch mount • Accelerometer mount • Compact and clean • Good cable management • Very rigid • Makes room for the X axis end stop cable Cons • -20mm in Y axis build volume • hangs too far forward IMHO • tolerances...

I printed the super awesome Flight Sim Rudder Pedals by the mighty Taumelscheibe. And I liked the pedals very much, but found them quite wobbly to the sides due to the construction. After some thinking and testing I decided for a broader footing...

This model is set up for vertical prints, requiring a 0.4 nozzle or smaller to capture the modulation circuit details. To assemble it, you'll need to drill out the hinge area for inserting a cut-off hinge that provides functionality. When put...

One magnet fits into each side of the stirrer, this becomes after printing and the positioning of the magnets and welded with the soldering iron etc. watertight at the edge. It should be noted that the opposite magnets in the stirring rod and in...

... your Quad setup. Key printer settings include: Printer: BQ Prusa I3 Rafts: No Supports: Yes Resolution: Mid (0.2) Infill: 20% Notes: When printing, please remember to include supports on the upper protection shell for optimal structural integrity.

20x8x1 spring** (stock extruder or bed springs should do the job, I use one of the typical yellow bed upgrade springs) * 1x **M8x50 bolt** (to be hobbed as drive gear: https://reprap.org/wiki/Making_a_Hobbed_Bolt) * 1x **M8 blocknut** (or 2 nuts...

Bill of Materials: Anti wobble: * 3/16" rods: + 8x 32mm * IGUS MYI-03-03 Flanged Bearing, 3/16 ID x 3/16 In L bearings (5 per pack - 4 packs, 2 spare bearings): + 16 * M5 heat set inserts: + 8 * M2 heat set inserts: + 4 X motor end: * M2 heat set...

We've worked hard to perfect our design, making two versions: one for normal material (PLA and ABS) and another for flexible material (printed with Ninjaflex). We even tested some early prototypes on ourselves and friends to catch any minor issues...

Print with no supports at 0.15mm and 15% infill. PETG is recommended as the mount needs to be a little bit flexible to work properly. So basically I wanted to use the DJI OM5's face tracking feature in livestreams and video calls but it doesn't let...

Case and bong mount may be printed separate if desired. If "laser bong body" is chosen be sure to use tree supports. Wiring is very straightforward. Red (positive) and Yellow (PWM) can each receive 12v, black (negative) simply goes to the negative...

Pause your print in your slicer at various heights to add multiple colours. New Update! Slightly larger tool box to fit the RC4WD Blazer Pickup conversions Dimensions ( RC4WD Blazer ) Overall Length from the lid 210.30mm (8.3 in ) Length...

... clashes with the top channels, but you can still get decent mounting on 4 out of 6 drives. Hole patterns: https://toshiba.semicon-storage.com/us/storage/support/faq/storage-holes.html Recommended to print with 0.12mm layer height. ...PLA is fine.

... I also put one on the back to keep the hot air that is expelled. These magnets measure 20x10x2mm, I'll include an Amazon link. https://amzn.eu/d/7u6znTt simply glue these magnets at the bottom in the designated places Printed on a prusa mini+

- Separate spacer that slides onto the 2040 extrusion mounting bracket to avoid printing the lower case with supports. The installation requires the following additional components: - M4 x 10 mm screw for attaching to the 2040 extrusion - M4...

All parts of the stand are included for you to mix, match, and remix as you please :) *All dimensions were measured after print* Medium Padlock stand: Height: 40mm Width: 36mm Length: 43.75mm Length of Lock resting area: 24.5mm Key holder inner...

- The AutoText function lets you automatically print the contents on the case: type, count and arrangement of the batteries. ##**Workflow** First select the battery type that you want to put in the case. If you don't find your model, measure...

The putty also helps keep the panels at the desired angle during experimentation.-KEEP printed and laminated protractors that they adhere to one leg of each stand with velcro to help students know the exact angle the stand is positioned at. -KEEP...

Suggested print color: Blue (scientifically proven to be most attractive to flies) Designed in Hong Kong. Warning Some species of flies can be extremely dirty. If you contact with them directly, wash your hands thoroughly before...

To assemble this version: Print one TOP part, one BOTTOM part, and two WHEEL parts. Carefully detach the covers from the sanitizer and remove the driver board. Remove unsoldered lamp leads and battery terminal wires. Insert the reflector/lamp...

The model in the pictures is printed with Hatchbox wood PLA that has been sanded, stained, and clear coated. It feels and sounds like actual wood so I highly recommend it, though any filament should work. It does take a little post-processing,...

if the provided printed gear is causing problems for you, I can recommend the gear in the following link's assembly. the gear is shared between Bachmann Thomas and Percy. this should be easy to substitute with paper clips or small metal dowels. just...

Here's a review of this tool on YouTube: https://www.youtube.com/watch?v=MXO_jLHvm8Y&t=3s Please read the print settings section below for important tips --------------------------------------------------------------------------------- This is...

... homelessness, poverty, and human rights. He has married twice and is the father of eight children. Thanks for checking in on us and for your ongoing support.CR8ED Out Of Hand Sculptor - Sandy Campbell3D Scanning and Printing - CR83D