acrylic enclosure 3d models

If you are printing in an enclosure, be mindful of having to potentially print off five or more for PETG, I've had one snap on me with the Drag Chain Adapter I remixed because I wasn't careful (bear in mind there's no screws on that design). PLA...

This is a small add-on for my IKEA Ender 3 enclosure. I wanted to store my tools convenient enough that they're not always lying around but also are pretty close, that I can get them in seconds. So I designed a very simple magnet holder. It's a...

Now I have added a camera enclosure that attaches to the back and flips to face either towards or away from the screen side, but with default settings camera picture faces up when pointing at the user, and is upside-down when facing back. It attaches...

I removed the hole in the back and made the enclosure deeper. Since the Raspberry Pi on the RatRig is located remotely, it won't be mounted on the back of the screen as is typical.</p><h4>Hardware Required:</h4><p>1 x Raspberry Pi 7" Touch Screen...

It's called OpenHead not only because it is fully open-source, but also because it incorporates open structure without any enclosures (unlike the stock T2 head, which is enclosed cube), providing you easy access for tuning and maintenance. The main...

It holds the membrane in place.Now the full part can be mounted to the enclosure with the original M-1J1R gasket going in between the part and the wall.If the box wall is too soft and bends a bit away from the gasket you can add the back plate to the...

http://www.thingiverse.com/apps/customizer/run?thing_id=49590 Instructions Using the following options: back_port2_position = 0 left_port5_side = top back_port1 = none right_port4 = none right_port4_side = top front_port1_custom_circle_radius = 0...

At first I was thinking about printing the entire enclosure. That´s why the source file includes a filament ring like the ones included with the dryer, just without the tray area. However, even so my printer can handle the size, it would be a...

Take a piece of painter's tape (I used the easily removable blue stuff) and cut a small strip with a straight edge that is long enough that you can grab and slide it between your eye and the lens enclosure. 4. Slide the tape into the gap and try...

The other parts could possibly be PLA but I find that PLA parts tend to warp and sag over time especially when the printer is located in an enclosure. I didn’t use any brass inserts. I made hex pockets in the parts to drop hex nuts into so that...

I created detailed instructions on how to print and build the shown device - just leave you the task of building the controller.Part 1 – Print the gearbox and base platePart 2 – Assemble the gearboxPart 3 – Enclosure parts and rotary table...

These universal hub clamps are excellent (I'd say even superior to any TUSH variant), but are a bit more cumbersome to change when fitted inside an enclosure, since some screwing is necessary. ...They are worth it though from a stability standpoint if...

 And unless you have an enclosure for your printer, layer adhesion on ABS prints may be weak.If you followed my recommended print settings, the first thing you will notice when you pick this up off your print bed is how heavy and solid this thing...

All of the electronics are housed in our 3D printed enclosure. The top and bottom covers snap fit so it’s easy to put together. It’s designed to be portable, compact device and it’s open source.</p> <p>In previous build we used several boards to make...

I aimed to resolve these issues and still fit the construction within the limited space available in the Photon's enclosure. I've read comments suggesting a construction placed outside the Photon, but I decided against it, opting for transparent...

Everything here on this design still works sufficiently to extract your fumes, but the additional option uses the desktop fume extractor with a larger blower fan and will move more air from the enclosure if you prefer. See x2 photos I have added...

PLA can work if you only ever print PLA, but if you plan on occasionally printing PETG, ABS or other higher temp filaments or if you use an enclosure in summer, you will need a higher temp resistant filament or it will deform and collapse. List of...

but dont do that unless you have an enclosure and can get up past 110C... Alternatively using alligator clips and an oven would probably be more effective... just don't go too hot... 110C for an hour is probably enough. I have also added a sheet of...

Have been working on this clock for a little while and needed an enclosure, and this one does the job very nicely (thanks to creator), and I used part of the Desktop widget clock for the screen insertion into the face (again, thank you). The original...

Enclosure for BigTreeTech TFT35-E3 dual-mode screen, for replacing the standard display on the Ender 5 Plus. <b>Requires a total of nine M3 bolts.</b> M3 × 8 mm (or longer - up to 12 mm) <b>×7</b> – four for holding the TFT35-E3 board between the...

You'll need to run the heatbed hot (60-70C) and/or an enclosure to keep the heat in. No need to print at a ridiculously high infill, 20% should be plenty. Any more you are just wasting filament.</p> <p>All up this will eventually clock in at around...

This video explain the problem for the big enclosure extractor fan and the small MC Fan. https://www.youtube.com/watch?v=3M76VUJzwqY (I don't recommend to replace the big fan by his alternate 12v fan and his step down regulator because an rpm error...

2 https://www.thingiverse.com/thing:5436065 Ender 6 Extruder Repositionig Relocation https://www.thingiverse.com/thing:4762567 Hand Filament Guide Remix Ender 6 https://www.thingiverse.com/thing:4762532 Ender 6 extruder hole cover...

Also added is a smaller version of the hanger, if you want to minimize things that go above the top of the frame (like, when adding an enclosure) or just to keep everything small. The first main photo in this feature is with the smaller hangers and...

The MeCreator 2, with its small size, ease of enclosure, and affordability, proved to be an ideal candidate. With further adjustments, the build volume was increased to nearly 170mm on the Y-axis and 165mm on the X-axis.Here you can see a video that...

This extruder working in an enclosure might not be quite happy... FINAL EDIT: The last minor design evolution and refinements, as well as the complete CAD data, 2d drawing and hi-res pictures are saved in:...

If you plan on printing in an enclosure, I wouldn't recommend PLA due to the fact these mounts will be carrying the weight of the bed and frame and the heat could cause them to warp/sag. You will need to print two of the mounts and two of the bed...

&nbsp;In case you're considering a similar low-runtime pseudo-UPS idea, make sure you calculate the ongoing power dissipation of the non-backfeed diode in your usage and make sure the diode can really handle that continuously inside an enclosure,...

This is a modular Single Board Computers enclosure for up to 4 devices. The<br>device cards are held vertically. This design let you service one card without<br>having to remove the cards on top of it like in the previous...

The build and schematics can be found at: https://www.printables.com/model/282166-runtime-counter-v-20 This box will fit in the enclosures made by Stepcraft. Hardware: DS 15 connector female (signal out) DS 15 connector male (signal in) Mono...