acer rubber feet 3d models

Here is a replacement rubber foot designed specifically for use with guitar or microphone stands. Conceived to fit securely within an inner diameter of 19.5-20.0 millimeters. ...Featuring a precision-crafted zoom function located on the slicer, users...

I've got a pair of old metal chairs sitting around, and the other day the rubber grommets that provide support for the legs gave out, so with my 3D printer's flexible filament at the ready, I figured I'd design some new ones.

Simple feet for Prusa I3 Mk2 to reduce noise and prevent slipping on the support surface.Can be used with or without the Prusa felt pads already on.Must be printed in a flexible filament like Filaflex, NinjaFlex or similar (Hardness 92A - 98A) for...

The original round feet i really don't like and don't match the design of the printer in my opinion, so I redesigned them.My design shapes are inspired by the chassis frame. ...Also the foot is a bit lower than the original so it gives more stability,...

These small plastic inserts replace the original rubber stoppers that fit into the metal scaffolding holding pots and pans in place. I had lost all my originals and opted to use these alternatives instead. They do get hot and slightly soften when...

To solve both issues I made these hexagonal feet that fit right into the Prusament spool. ...You will need to print six of them to cover all nuts and bolts.Print settings:0.1 Detail preset on the Mini+;Fiberology Fiberflex 40D configuration from...

I recently experienced a sudden, unforeseen deceleration while operating my Mavic Pro drone, resulting in the loss of one rubber foot on its rear end. To rectify this situation, I decided to attach larger legs, which prompted me to search for a...

These are Feet for a Nintendo Gamecube, the front fit a Standard OEM gamecube were as the back are designed for the recreated Gamecube shell that i made. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: Yes Supports: Yes...

As I had TPU material readily available at home, I created a design for small feet in SketchUp. The screw goes inside and once tightened, you need to insert the tips to cover the screws. This setup minimizes contact surface area, resulting in less...

I write in conditional because I've only been using these feet for a few days, so I have no verification that they won't warp after a month. Of course, it is possible to both increase the number of perimeters and specify an infill for higher...

I designed this print specifically to fit snugly within my 2020 extrusion corner brackets - a diameter of approximately 12.5mm should be measured in your own brackets before printing, then adjust the scale accordingly for different sizes. To achieve...

Print four objects using a Ninjaflex filament, then attach them to the underside of each leg using Super Glue for secure adhesion.

Wanted my Brewtools B80 to sit a little bit "softer" on my bench. Printed in soft TPU, no supports needed.You would need 6 side pieces, 1 front piece and 1 rear piece for full coverage around the lower rolled metal edge. ...But you can easily just use 4...

ich habe die Füße aus TPU gedruckt! ...Ich denke bei anderen Materialien (PLA, PETG) könnte die Leiter wegrutschen

Customized version of https://www.thingiverse.com/thing:3453817 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3453817

It's a Customized Foot for the Harman Kardon GoPlay 2 Speaker System. Printed at Extremely High Heat, Reaching Scorching 932 Degrees Fahrenheit. ...Layer Height Set to an Ultra-Thin 0.2 Millimeters.

Customized version of https://www.thingiverse.com/thing:1904304 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1904304

Wanted my Brewtools B80 to sit a little bit "softer" on my bench.Printed in soft TPU, no supports needed.You would need 6 side pieces, 1 front piece and 1 rear piece for full coverage around the lower rolled metal edge. ...But you can easily just use 4...

Customized version of https://www.thingiverse.com/thing:3453817 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3453817

This creation was crafted using Tinkercad as its foundation. ...Make adjustments directly online at https://www.tinkercad.com/things/3eomR9KB36g.

Printed with flexible plastic material The worn-out one snapped I extracted the rusty screw And I installed the shiny new one

<p>Easy print with no effort at all. Make sure to print it slow. ...Otherwise, you will get a fail print.</p>

Customized version of https://www.thingiverse.com/thing:3453817 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3453817

Customized version of https://www.thingiverse.com/thing:3453817 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3453817

Customized version of https://www.thingiverse.com/thing:3453817 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3453817

This pad is designed for use with 3D printers, specifically the MK2X/Rebelix model. To secure it in place, screw the extrusion profile into position using an M5 screw, nut, and washer. The pad itself is made from 3DFila flexible filament. ...If you...

<p>I made this for a piano's base, they are horizontal, but I made a vertical position too.</p><p>You can use it for any size square tube by adjusting the scale on PrusaSlicer. ...&nbsp;&nbsp;</p><p>These are made using FLEX filament at 0,3 layer...