abus granit detecto x plus 8000 3d models

Made this spool holder to be able to mount large (300mm) spools to the X-Plus, as the spool holder rods dont't extend long enough to properly support those. May not be the smartest solution, but works for me. Be careful with spools that are fully...

QIDI X-Plus 2 Dial Indicator Mount using a dial indicator from my local Menard's. Stem size .375". ... ...

This X-Axis Extruder Mount is specifically designed for these models, guaranteeing precise alignment and stable operation. Its durable construction withstands rigorous printing conditions, minimizing vibrations and noise that can affect the overall...

I noticed that my PrintrBot Plus V2.1 would have problems printing very tall objects - towards the top of the Z axis, the small amount of wobble of the z-axis guides is pronounced and leads to the sides being slightly closer together. This causes the...

With that goal I designed both an X and Y tensioner for my Duplicator i3 Plus. Hardware required is listed below and adjustment is meant to be done with a ball end hex. ... Adjuster Bolt for Both: - Button head Hex M3x16mm, Two M3 washers and one M3...

The Anet A2 Plus X belt tensioner is designed with a focus on the y-belt tensioner used in the Tevo. To prevent rattling and allow for x-axis tilt adjustment, an eccentric nut was incorporated into the design. The dimensions of this eccentric nut...

BIQU B1 SE Plus X Axis belt tensioner.Print housing standing on end where insert goes throughPrint Insert on end with screw facing upNuts print at 105% X&Y (Not Z axis) Your results may very to get nut to fit.Housing V2 has a solid top to make it...

Anet A2 Plus X Motor Holder To prevent the timing belt from rubbing against the axis position of the A2 motor holder, I shifted its alignment. Alternatively, I could have replaced the original parts, but I decided to create a custom solution instead....

Awesome Very low resistance Spool holder for Qidi Tech X-plus 3d Printer Makes printing TPE and other exotic filaments a little easier, the bearings lowers the resistance when pulling from the spool. Printed 100% infill for my own use, all parts.

Made this spool holder to be able to mount large (300mm) spools to the X-Plus, as the spool holder rods dont't extend long enough to properly support those. May not be the smartest solution, but works for me. Be careful with spools that are fully...

This is an upgraded version of the Qidi 3D X-Plus Spool Roller, crafted by mistertech, where two critical parts are replaced with a more substantial structure. The original files, Spool_Roller_lock_170mm.stl, which held the assembly together, have...

I faced issues with my PrintrBot Plus V2.1 printing very tall objects, where the Z-axis guides wobble led to slightly overlapping sides near the top of the Z-axis. This causes X-axis belt tension to become loose, despite being tight at the bottom. I...

the white 5050 LED strip in the front of the X-PLUS doesn't really show you what is happening at the nozzle. Is ok for gneral viewing.. The LED strip can be cut into 3 sections, and connected with extension wires if you want to put them in a few...

Print Settings Printer: Anet A8 Plus Rafts: No Supports: Doesn't Matter Resolution: .3 Infill: 25% Filament: Inland PLA Rainbow 2 Notes: Part currently printed in PLA Silk as that is what my only working printer had loaded at the time would recommend...

This is an upgraded version of the Qidi X-Plus 3 Carbon Filter that comes with the new models. This may require modifications of the back panel. If you don't currently have the carbon filter installed there is a template and instructions that are...

As part of my ongoing upgrade of my A8 Plus, this clamp is designed for the X-axis belt on the carriage, replacing the stock (rather poor) part with a solid one and eliminating the tensioning facility in favor of an external tensioner, which I've...

Print Settings Printer: Anet A8 Plus Rafts: No Supports: Doesn't Matter Resolution: .3 Infill: 25% Filament: Inland PLA Rainbow 2 Notes: Part currently printed in PLA Silk as that is what my only working printer had loaded at the time would recommend...

After a year of almost daily use, the plug-in connection to the heating bed of my Qidi X-Plus said goodbye without comment. See photo. Fortunately, the power of my ancient Weller soldering station was sufficient to solder the pin strip back on...

To undertake this mod, you will need to purchase: • 2 - 7/16-14" x 36" Steel Threaded Rods • 8 - 7/16-14" Nuts • 6 - M4x15mm Bolts • 6 - M4 T-Slot Nuts You will need to print: • 1 - Upper_Left_Mount.stl • 1 - Upper_Right_Mount.stl • 1 -...

Since uploading my Ender 5 Plus Micro Swiss cable support bracket, I have redesigned a bracket to fit at the end of the X Gantry to mount the cable on to support it away from the metal frame and the wheels on the gantry. You will need to install this...

Great 3d models of De Majo 8000 suspension and wall lamps have been created, showcasing outstanding details. These models are based directly on the manufacturer's original dimensions, ensuring accuracy. Available formats include: .max v-ray -...

If your Dremel 8000's axle-lock button has snapped, just like mine did, you can 3D-print a sturdy replacement instead of trying to glue on the flimsy original. Don't worry about the messy residue or rough top layer - this is a functional part, after...

... for Anet A8 Plus. ... Combination of various components from Thingiverse, tailored specifically for the Anet A8 Plus. ... You will need to lengthen cables for FAN1, FAN2, EXTRUDER Thermoc Controller (two white cables), and MOTOR Extruder (four cables).

A Custom-Made Bumper for Your Abus Lock Crafted from flexible filament, this innovative bumper is designed to provide a precise fit for your Abus lock, ensuring optimal performance and reliability.

[For details and most recent files please see PrusaPrinters.org](https://www.prusaprinters.org/prints/73353-abus-bike-lock-keycap)

Abus ulock mount for Decathlon cargo r500e oct-2023 version.printed with PETG a 0,6mm nozzle, 60% infill.

I designed this spool roller to clip onto my QIDI X-PLUS printer, where it replaces a built-in holder that I found created too much friction, especially when printing with TPU material, which caused frustrating voids. To solve this issue, I opted for...

... the bolts back down. BOM: (1) M4 eye bolt (repurposed from stock y-axis tensioner) (1) M4 nut (2) M3 x 10mm socket head screws (6) M3 x 20mm socket head screws (3) M3 Washers (1) M4 Washer (1) Epoxy - for gluing the M3 x 10mm into the teardrops

It is a simple way to get filament rolls to turn easy on the QIDI X-Plus. I had problems with the original piece that holds the bearings. They seemed a little thin and I couldn't slide the QIDI spool support rings over them either because it's a...

I am proud to share with you this exact replica of the legendary omniwrench 8000 from Ratchet and Clank's Tools of Destruction, carefully crafted in SolidWorks for my inaugural project. The painstaking process consumed nearly a week of my time, yet...