abus granit detecto x plus 8000 3d models

It can be used in 2 ways: + or X, as you prefere, have fun to mix it in differents colours or combinations! With its 3.5mm hole it can be fixed with only one screw, and is strong enought to be pulled every time you need! Stop searching everywhere,...

grain car GRANIT blue and black right side model HO scale printed with an ENDER3

This is designed to work with the ABUS Granit X-Plus 54 Mini U-lock, and be mounted on the Boosted Rev electric scooter, which has a 38mm diameter tube.It may work with other similar sized locks, but I have not tested it with any other ones.For...

SNCASO SO.8000 Narval.

The Vehicle is Equipped with a Powerful Tandem Axle System, Capable of Supporting an Impressive 8,000 Pounds, Spanning 86.5 Inches in Length and 60.5 Inches in Width. ...This Robust Design Features an Over-Slung Suspension Configuration, Providing...

My SD Card Multiplied 8000 times. ...Enjoy.

Made for Anet A8 PLUS. ... x axe belt holder.

Abus Amparo replacement cap.

This is the X-belt tensioner of the Anet A8 plus reviewed and corrected

Just a simple 8000 Lb. Fork Truck I modeled. 54" forks 8000 Lb. ...Capacity 60" Wide 148" Overall Length (Including Forks)

cooling fan duct for qidi x-plus This fan duct is only a replacement part for the original design. ... (there are different designs for qidi x-plus, so it should look like this one)

A versatile person is somewhat unsuitable to handle a Kodak 8000 panorama machine effectively.

Qidi tech X Plus - top cover closing plate - with thermometer hole, with filament hole or just blank. ... As thermometer used Afriso 63826K - 0-60 grad

This is a little modification for original X-Plus Extruder Fan. ...Print this model then replace from two stand-off to this fan duct.

this is a compiled and edited version from several source of Anet A8 plus x belt tensioner works like a charm, just like the original

Blink Camera Mount for the Qidi X-Plus 3D printer. ...This mount attaches to the back left bar and puts the camera in front of the fan.

Dimensionally accurate 3D model of the Motorola DynaTAC 8000 battery. ...Original battery provided as reference by Zhinü Luó.

This is needed if you close the hole in the hood with for example @humebeam QIDI X-Plus X-Max Top Cover https://www.printables.com/model/59198-qidi-x-plus-x-max-top-coverPretty simple design, print on it's side, no support needed, take the original...

Simple mount for BL Touch to fit an X-Plus 3. ... This is meant to be used in the Back mount replacing the existing sensor on the pre upgraded X-plus 3. ... M3 screws can be used to attach the BL Touch without the need to use nuts.

Designed to help assist with bed leveling for Qidi Tech. ...X-Plus. Squares are large format 50x50mm and printable area is 250x180 mm. ... Designed to be printed on a single layer with a .04mm nozzle at .02mm layer height.

Any filament should work but would use something more temperature tolerant than pla. ... Might have to clean up surfaces to get magnets to sit perfectly level with build plate.  18 are needed for the x-plus build plate.

The original spool mount by Skiid dosent fit the new QIDI X-Plus 2 printer. This is my first remix but the mount fits great. The part that I changed was the little hook part of the mount. ...

x_end_motor.stl from https://www.thingiverse.com/thing:3716110/files > bear_extruder_x_axis_mk3s.zip Plus, download and print: 1. z_motor_mount_front.stl 2. ...z_tops.stl from https://www.thingaverse.com/thing:2808408/files > bear_full_upgrade_mk3.zip...

a little Rain Cover for a ABUS KeyGarage. ...

Replacement part for a knob on the ABUS combination lock.

Designed to help test bed level settings on Qidi Tech X-Plus. 3 rows of 50x50 mm squares to show where adjustments are required. Designed to be printed with a .04mm nozzle at .02mm layer height. ... Printable area is set to 250 x 180 mm

BIQU B1 SE Plus X Axis belt tensioner. - Print housing standing on end where insert goes through - Print Insert on end with screw facing up - Nuts print at 105% X&Y (Not Z axis) Your results may very to get nut to fit. Hardest part is assembling...

These files match the original X-axis belt tensioner found in the Anet A8 Plus kit, but I encountered problems with the belt slipping out occasionally on my end so I decided to upgrade the smaller component of the belt holder allowing you to loop the...

The X-axis belt tensioner is an essential component for the Anet A8 Plus 3D printer. This device ensures that the X-axis belt remains tight and well-adjusted, providing a smooth and precise movement of the print bed during the printing process. The...

Modeling was done using Blender, while printing was accomplished with QIDI X-Plus. Before initiating the print job, verify that the scale is accurate to avoid any potential issues. ... Printing Details: Material: PLA Infill Percentage: 80% Layer...