abstract desk 3d models

To Use Use an LED flashlight or halogen desk lamp to shine into the reflector area below the slide stage. It may take a little experimenting to get the light right, but you should be able to evenly illuminate the slide background screen. You will...

For now, it gives you enough height to keep the impeller off the desk while you test it. Pop the motor and clamp into the top side, push the impeller on from the other, run some power to the motor straight from the batteries and figure out which way...

The options are: Stand the frame on a table or desk with **ModularFrameDeskStand**. This is a print-in-place hinged stand. Snap in one or two of these in the bottom edge of your frame. Not recommended for pictures larger than 8"x10". Hang the...

In my case I could make a corner profile in the 330x330x400mm desks ;-) . But it is also possible to put several profiles together with a suitable threaded rod, but a seam can be seen.</p> <p>The holes in the corner profile are then intended for...

- You can mount the boxes to each other using the rails or mount them to a wall and easily slide them off, put them on your desk and once you are done put them back on the wall. - There are 2 sizes of bins that slide into the top or sides if you...

For example, you could insert LEDs into some of the shards or use our illuminating base to create a desk lamp. See: https://www.thingiverse.com/thing:4850163 [![illuminated...

For example, you could insert LEDs into some of the shards or use our illuminating base to create a desk lamp. See: https://www.myminifactory.com/object/3d-print-arduino-nano-neopixel-ring-base-171564 Versions 1.2 (14 Jun 2021) Added support for...

I also found that most caused the marble to fall off if there were any unwanted vibrations from the motor or the desk being bumped. I failed at that as stability becomes a problem over a couple of feet. I'm thinking if I should try to solve this...

What started as a tray to keep my SD cards, thumb drives from being scattered all over my desk, I thought I would turn it into a “better looking” sculpt rather than print a tray for a stand . . and so . . . the first of two sculpts Redfox Bath Night1...

The cable from the print bed was always hitting the wall and at the front the electronics box was sticking out over the desk. I had to remake many parts and adapt existing ones to the dimensions of the S8 Pro, as the main project was for the CR10....

You can then either sit it on your lap or lean it against a desk and weave however you please. When done, simply fold it up and put it away; it's small enough to fit inside a satchel. If interested in the craft of tablet weaving, search YouTube for...

This is intended as sort of a useless desk toy that points at the location of the international space station in the sky. You can also tell it to point at other things, of course. Final goals are to make it fetch TLE data from the internet, and allow...

https://www.amazon.com/gp/product/B07GSNBGHY/ref=ppx\_yo\_dt\_b\_asin\_title\_o06\_s00?ie=UTF8&amp;psc=1 I recommend small hemispherical self-adhering rubber feet to raise the base above your worksurface/desk/cabinet. Doing so allows the cables to...

I made a decorative desktop water fountain to liven up my desk space! The fountain makes a pleasant water trickling noise and operates independently. I need top up the water reservoir every three days or so because of evaporation. **Required...

....Also it is a fun desk ornament for physics fans. As always I will promote and REWARD the first people to post quality makes (must enable tips on your profile for reward). A quality make is a successful, complete, hopefully decent looking print at...

8Bit PAC-MAN's ghosts are back as a decoration (and/or light) for your computer desk or the shelf next to it.&nbsp;Easy to print and colorful brings back memories from that golden age where the video games are start to rule the world. Its easy to...

Buttons can be more easily mounted underneath the desk so that the knee can be used. Buttons can be easily mounted so that affected limbs have to reach out to press them. And of course, buttons can be more easily accessible because gaming should be...

(right side tilt drawer coming soon)HARDWARE• Screw Driver (Long narrow screwdriver or a screw driver with a shaft longer than 105mm )• Screws: 3x12mm wood screw or #4 x 3/4 inch screws• Drill bit that is smaller diameter than the wood screws• Use...

To remove one extra cable from my desk, I integrated a Raspberry Pi 3B with Octoprint inside the case, along with a Sonoff switch for remotely turning on and off the printer. On the PSU, I installed a 60mm silent fan (the original one was noisy),...

There’s also a 3D-printable mount to work on your robot head on a table or desk. <b>Enhanced Movement:</b> Experience greater up/down eyeball movement range and a standard-sized servo for head side-to-side movement, saving space and cost. ...

I still regularly use discs, and didn't want to clutter my desk with an external enclosure. I considered buying a different case and swapping all the parts, but unfortunately in general it seems difficult to find decent cases with 5.25" bays...

The Desk_Set_Example.stl file is the object created by default values when you open the .scad file in Customizer. It shows some of the options for columns. It uses 8 of the possible 10 columns and a variety of sizes, shapes, and twists. You are...

And here comes the idea of this magic blocks, that you can put on the desk to colour your days, or hang to the wall and use as hanger for keys or light cloths, to recreate the energy and positivity that Mario only can give. In this second case I...

Despite my printing it and it working for a bit, there's a long way to go before it's a polished product.&nbsp;I wanted my succulent to thrive on my desk, but it just couldn't get enough light. So I made this self-sufficient planter enclosure with a...

If you have a PTFE lubricant or other lubricant that is compatible with your choice of plastic, when final assembly has been completed a light greasing of the lead screw will help operation.OptionsThe options are provided in separate 3MF...

The tighter the string or rubber band the more power.There are a few options at this stage:First of all, you can leave it at this stage and just start pinging stuff about your desk, or you can fit a firing mechanism. For mine, I used 3 small brass...

The idea was to make miniature spotlights that can be controlled via a standard lighting controller, like the one we use in the theatre I'm working at. You can open and close the barndoors, as well as move the whole spotlight around, just like a...

or just make make it easier to work on PCBs at your desk... whichever comes first. You loved the original E-Vise; now get ready for a banger of a sequel! Introducing the E-Vise V2! Blessed by the angels of mechanization, this absolute god tier...

You see the future and prognosticate instant access to all of the information in the world from a device that sits on every person’s desk at their office. Microfiche wouldn’t come along for another 14 years. But you see the future. And the modern...

The outlet openings in my case are at the bottom because the cash desk is placed on the printer cabinet, but they can vary according to personal needs. The interior is covered with heat-reflecting material to avoid heat loss and also to slightly...