a10 freewing 3d models

... 2x Tapping Screws. It might work with other printers that use same kind of frames e.g. Creality Cr-10, Geeetech A10. Please leave a message if it works on your printer. ... This is a remix of this thing: https://www.thingiverse.com/thing:1986658

This is a replacement handle for a cooking pot cover (Brand Tefal). 1 x TefalHandle : Layer:0.20mm Raft:no Brim:yes Support:no Infill:100% Dimensions: l=36mm L=73mm H=29mm Hole=4.5mm Print instructionsPrinter: Geeetech A10 Rafts: No Supports: No...

This adapter allows creating a control box extension cable for the Geeetech A30 control box, as well as other Geeetech models such as A10/A20. A panel-mount style M20 aviation connector is used in this adapter. These connectors are generally easier...

So I made a adapter to fit a VKB to the Obutto Thrustmaster A10 Warthog mount.Remixed from https://www.thingiverse.com/thing:5445317Just heat press in some M4x8x6 Threaded Heat Embedment Nuts...

Main gear door mounting bracket for the Freewing 90mm F-22. I opted to use concentric supports on models with rounded ends because they seem to print cleaner on the bottom side that way. The model with square ends prints fine without any supports,...

Many parts are from the Freewing Avanti ARF. ... Print using LW-PLA and clear PETG Powerplant: 80mm Cell Count: 6S Wingspan: 45.75 inches, 1 piece removable Length: 46.4 inches Files include STL files as well as the project files from PrusaSlicer ...

I designed this K-13 Atoll missile for use on my Freewing Russian jets. This is about 1/14 scale. You can scale it up/down as you need. I suggest printing the rear with a brim and the nose with supports. If you like my designs and find them...

I designed this R-77 Adder missile specifically for use on my Freewing SU-35, and it's about 1/14 scale. Feel free to scale it up or down as needed - I suggest printing with supports for optimal results. I've also included an alternate tail section...

I designed this R-27 Alamo missile for use on my Freewing SU-35, scaling it down to 1/14 of its original size. You can adjust the scale as needed and print it with supports if desired. If you find my designs useful and appreciate them, a tip would be...

This is a 1/12 scale GBU-8 HOBOS guided bomb specifically designed for the Freewing F-4 Phantom model kit. I'm also interested in acquiring a wing pylon that replaces the standard one included with the Phantom, which typically holds Aim-7E Sparrow...

I crafted this R-73 Archer missile specifically for my Freewing SU-35 model, scaling it down to 1/14. Feel free to adjust the size to suit your needs. My design includes thin supports between the two fins on the nose cone; simply clip them off after...

They are slotted to use the weapons mounting hardware from the Freewing 90mm F-16. The missile rails replace the molded foam ones that come with the jet. I also cut the fuel drop tank off and added a weapon mount to it so that it can be removed...

If you're interested, check it out here: https://www.thingiverse.com/thing:3592144 The AIM-9M Sidewinder missile has been scaled down to 1/11.5 scale, matching the size of the Freewing 70mm F-16 V2 model. You'll also need to print the pylon...

The 2-part box is designed specifically for the Mobius "ActionCam" camera, featuring an attachment point that seamlessly fits Freewing R/C aircraft weapons pylons. This allows users to easily mount the camera on their aircraft. For optimal underwing...

I designed this EDF test stand to facilitate the selection of my EDF's for the Freewing T-45 Goshawk. In addition to the pressure components, you will need two 8 x 70 mm steel rods, plain bearings and a few 4mm screws. ... The Amazon links provided...

This is an aerodynamic box designed specifically for holding a Mobius ActionCam camera, ideal for mounting on Freewing R/C aircraft weapons pylons or any other object with compatible mounting hardware (consult notes below). The camera box comes in...

The pylon uses the 90mm Freewing F-16 weapon mounting pieces. The male piece goes in the wing and two female pieces go on the pylon so it is removable. The pylon is indexed to position the female sockets the correct direction. If they don't fit...

To secure the attachment hardware, I utilized the existing setup from the Freewing 90mm F-16 model, effectively holding the weapon in place. However, unlike the original pocket with magnets, this version features a slot located in the center section....

Tested on an A10, probably works also on A10. You will need to: Print a new Y endstop mount because the cables are not really long on this machine. Make an extension power cord to use the PSU in its original position; mine is on a side on the back...

This case is specifically designed for the Geeetech A10 2560 v3 board that comes with most modern Geeetech A10 printers. I attached this case to the underside of a Lack table, turning my Lack Enclosure into a sleek and functional printer housing...

This is a remix of the knobs I made for my CTC A10S, a CR-10 clone, after one of the miniature factory nuts disintegrated. These thumbwheels require a M4 nut for each. Unlike my previous model, these print as a single piece that will likely...

Designed to fly on 1/2A to A10 rocket motors. My test print weighs 1.38oz without a motor. Test flown twice so far on 1/2A motors in my backyard. Probably around 70ft high, no parachute needed on grass. Should be about 175ft on an A10. This design...

... A20M at https://www.thingiverse.com/thing:4240378. If you're also in need of a purge bucket for your hotend, take a look at the E3D V6 Purge Bucket for Geeetech A10M A10 A20M A20 available on Thingiverse at https://www.thingiverse.com/thing:4459509

... ...I designed it for my CTC A10s "Creality CR-10" knockoff printer, but can be used on most any printer that uses T-slot extruded aluminum rails for a frame. I attach this to the front left corner of my printer using 2 1/2" M4 screws and 2 M4 T nuts.

This is a custom motor mount designed specifically for the Lidl glider's Hacker A10-13L motor, tailored to fit perfectly with a 30mm spinner. The design accommodates different motors by adapting the hole pattern without significant modifications. To...

This small rocket model is designed for an A10-3T engine, with a slightly tight initial fit that has been adjusted by adding 0.5mm to the diameter. The .stl file, Rocketparts.stl, includes a nose cone and fins suitable for C-rocket engines, requiring...

The quad rotor-craft airframe design I am creating as part of my degree project aims to develop a ground support aircraft, potentially replacing the retired A10. Additionally, it could be used for medivac and light transport missions. This initial...

Printing this leveler at 100% infill took approximately 30 minutes with my CTC A10S (a CR-10 clone). Following printing, a soldering iron can be used to install the threaded insert nut. Insertion from the bottom side is easier. Once some extruded...

... Print Settings Printer: GEEETECH A10 Rafts: NoSupports: No Resolution: 200Infill: 25% Filament: Protoplasta HTPLA Blue Notes: The hole on my printer came out a bit small so I had to widen it a little. ... Category: 3D Printer Accessories

... + print wheels + option print floor Choice 3: Print top + print part on the road with wheels included + option print floor Ho Scale File Vint87vanFull.slt, Print fine quality with raft/support. - (Good settings on my GEEETECH A10, no problem)