a10 3d

I had a lot of trouble finding a fan duct model which worked on the late 2018 version of the Geeetech A10 - all the versions I found were too wide and didn't work. ...This is a reimplementation that's close to the original, with some modifications for...

On Geeetech A10, the X Belt sits 5+ mm lower than its pulley counterpart. This discrepancy causes the X travel not to be perfectly even throughout its entire range, as movement is calculated along a triangular path. ... A spacer is designed to correct...

This is an additional type of board fan cover designed specifically for the Geeetech A10. ...I've dubbed it "Bridge-It" due to its unique feature where the uppermost layers double as a testing ground for your bridge settings, allowing you to fine-tune...

Remixed for Geeetech A10 [HW ver. V5.10], a cutting-edge motherboard upgrade. This particular remix may not be compatible with earlier versions, so proceed with caution. ... This is just one part of the entire remix; for the complete files, please refer...

Round buttons for A10 CDU Simulator. The dimensions are from oriignal device. Text are"engraved" deeper to help paint the numbers. They are meant to print with a resin printer. I did the engraving with bigger numbers. ...now they look more realistic,...

GeeeTech A10 A20 A30 fan duct for stock hotend and Bl-touch Included adapter for e3d v6 and clone [Dragon hotend] Suggested PETG or ABS for FanDuct parts Required silicon socket or isolating pad for hotend block Spare part : M3 different length

Stand up a miniature A10 scale model with precision, scaled down to 1:16. Visit https://www.thingiverse.com/thing:3047962 for the downloadable design. To prepare this intricate model for printing without any support, slice it carefully at 42mm from...

I fixed the faulty filament run-out sensor on my A10 printer with a straightforward and efficient DIY solution. ...The repair involved replacing the defective clip, which was easily achieved by following the instructions in this helpful video:...

This is a Print Head Cable Holder for Geeetech A10 printer.On several occasions, the electric cables of the print head have cut off due to very large movements on the X axis. ...This device avoids any stress on these cables.

... ...This one fits easy on the Geeetech A10 or A10M. I made a "blank" one to print easiert. After printing you just need to drill the 3mm holes. Unfortunately I can't linkt the remix. ...All credits go here :) https://www.thingiverse.com/thing:2494642

Extruder Mounting Plate to Mount the OmniaDrop Extruder to a Geeetech A10 Carriage Plate Print Settings: I recommend printing with 100%infill for most stability since its a crucial part for precision on your printer. Its supposed to be mounted...

Industrial-grade leveling wheels designed specifically for heavy-duty use on the A10 machine. These robust wheels ensure accurate and stable positioning of the large bed, facilitating precise control and smooth operation during production runs. ...Made...

Case runout sensor filament genuine Geeetech A10 https://youtu.be/SXra5cUiGBw ------------------- Look at this my project! ... https://www.thingiverse.com/thing:4623521 Follow me please for more projects ;) https://www.thingiverse.com/duegi/designs ...

This is the left and right side nacelle frame for the FT A10, specifically designed to accommodate a 5-inch propeller. ...The nacelles are approximately 4% larger than those included in the standard speed build kit, necessitating slight adjustments to...

Unfortunately one of the wheels fall of on my E-Flite UMX A10 on intial setup of the airplane. This spare parts can be drilled with a 1mm drill and then put on the axis. ...Pls fix it with glue if you want to keep all wheels :-)

This is a community forum dedicated to improving the Geeetech A10 V4.0, specifically designed to minimize noise pollution and prevent filament from escaping onto the motherboard. ...By reversing the fan's airflow direction, this redesign offers a...

I'm excited to share with you a customized version of the Geeetech A10 LCD Back cover plate that I've designed specifically for the 2018 version printer! ...Don't forget to route the cable safely before securing it in place with screws.

This is a Dynam A10 Warthog, which needs to mount a Runcam Split to cover up the deck that must be removed for installing an FPV camera. ...Take a look at this sample of the Runcam's FPV position: https://www.youtube.com/watch?v=k5D0_0fw4OY

Geeetech A10 Z-axis head replacement part. I received my printer with this crucial component shattered. My first task was to craft a brand new one. I enhanced it for users running single-extruder configurations with PLA filament guides. ... Please,...

... design. ...To accommodate the Geeetech A10, parts were carefully extended to ensure a precise fit. The plexiglas plates used in this build measure 3 at 48cm x 44cm and 2 at 48cm x 22cm, all with a consistent thickness of 3mm. ... Have fun using it!

Set two of square butttons for A10 cdu Homepit builders, if you have a resin printer, it is better do a print job with whire opaque resin, if you want those backlighted. Sure you can paint those numbers and letters too.. ... Special buttons are little...

This is a compact design for the Geeetech A10 LED light bar, created to address the issue of the original mounts being overly lengthy, causing the light bar to collide with the bed in the initial project.\r\n\r\nOriginal project reference:...

... el conector de la cama caliente en la Magna V1 / Dual. ... Se fija por debajo de la pieza de chapa, utilizando dos precintos. ______________ Cable Relief for the Geeetech A10's heated bed. For fixing, used the stock metal part over the cable. ...

I collaborated with Hermiedug from thingiverse.com to develop a solution for an issue on older A10 versions, where it lacked the Hotend PCB. This fix addresses the problem of Extruder wires rubbing against the sharp metallic edge of the extruder...

During this time with Geeetech A10 I noticed that while is working sometimes the connector of hotend does not work properly, sometimes making stop the printing. I designed this cover with a support to make connector and cable more stable. This cover...

Fan duct for geetech a10/ magna 1 printer. Its a remix from mazzoca model -> https://www.thingiverse.com/thing:3205029 In this model, I try to improve the airflow, the angle was modified to avoid the mk8 nozzle, with a little wing in the exit...

But I decided to share what I've done so far and maybe it can help some to use this great design made by 3D_Bus_Driver. Since I noticed a lot of gaps, print tolerances and accuracy, etc, I decided to leave the Plexiglass measurements to last. ...

I replaced the mainboard of my A10 and decided to use sensorless homing (with TMC2209 stepper drivers) instead of mechanical switches. So I needed to replace the X/Y micro switch end-stops with a bumper. Both bumpers consist of two parts: One none...

On the left side of the A10 there are 2 small holes where the cables can be hidden well. The LED strips are connected either: - at the lower case fan (24V): The LEDs switched on directly with the printer. - or to a free bottom fan. Then the...

... Additional components needed: 4 M4x6mm screws 4 T-Nuts M4 Optional: LCD Display Holder Left Side Geeetech A10: https://www.thingiverse.com/thing:4098947 Silicone damping feet with adjustable height: https://www.thingiverse.com/thing:4108039