a frame brace 3d models
2563557 3d models found related to a frame brace.thingiverse
This is a Anet A8 frame brace for(if your looking at the front) the right side. This is to help stiffen and give support to the X axis. I also believe it helps with the Y also. Here are the details of the print: Material: PLA - Any material...
thingiverse
This is a remix of NSD3D's CR-10 Frame Brace. He did an excellent job at designing this brace. The issue I had is that my CR-10 has the Dual Z Mod which his brace would interfere with. So I modified his design that when it mounts to the CR-10 it...
thingiverse
This is my version of a frame brace for a Creality CR10S as I think many of the others on Thingiverse are too large and complicated. Left and right braces are the same so print two of each. It uses M8 threaded rod but 5/16" would do as well. I'm...
thingiverse
A frame brace for the Anet A6 middle section with 3 screw holes. It is a slightly modified Version of the back frame brace from Henkolizer. ...Print Settings Printer: Anet A6 ...
thingiverse
I've never been a fan of the threaded rods solutions, and since 2020 extrusion is easy to source and assemble I created a frame brace with it. Materials: * 24 M4x8 screws * 24 M4 t-nuts * 2 500mm 2020 aluminum extrusion It is using 4 screws to...
myminifactory
This is a frame brace for the Prusa Research Original Prusa i3 MK2S. It was designed to remove flexibility found in stock setup as well to ease threaded rod fitment-to-brace that can slip during adjustment or tightening. It does not however...
thingiverse
A simple frame brace for Prusa Mendel minimizes z-axis wobble at high head speeds. Assemble a complete brace by printing two pairs of braces using M8 threaded rod (110mm length), ten M3x20 screws and nuts, or 4-40x0.75" screws and nuts. ...The design is...
thingiverse
This is a Einsy Frame brace, I had made this to help remove the small bit of play the frame had where the einsy board is since there is wire movement at that spot. ... Printed with PETG 40% - Infill 5 - Perimeters Screws required: 4 - m3x18 2 -...
thingiverse
The Prusa I3 Y-corners, when combined with a frame brace, can be improved by following this design on Thingiverse (http://www.thingiverse.com/thing:251890). ...This modification involves removing the top nut hole to facilitate easier tightening of nuts...
thingiverse
https://www.thingiverse.com/thing:4079138 I bought a used JG Aurora A5 printer and found that the vertical section seemed a little weak to me so I did up a quick frame brace to add some strength to the area. Its a little crude and has been swiss...
thingiverse
This is a simple frame brace design that uses two 24" (610mm) lengths of 2020 extrusion available from McMaster Carr. All hardware is also available from McMaster Carr. ... Printed Parts List: 1x extrusion_brace 1x extrusion_brace_2 2x...
cults3d
Frame reinforcement system with only printed parts and 8mm diameter aluminum bars. ... Totally interchangeable between top bottom left right.
cults3d
It's a set frame brace for CR-10S 500 Series. You'll need stuff as following: A. The length about 735~745mm M8 Thread Rod 2 PCS (SUS304/316/430) B. M8 hexagon Nut 8 PCS C. Narrow type M8 Flat Washer 8 PCS (Optional) D. M5 button head screw 12mm 12...
thingiverse
After I made up a frame brace (https://www.thingiverse.com/thing:2626456), I realised that with some small modifications, it could also be used to secure the frame to a (wooden) base when installed between the Y-rail and the XZ frame... So I made it...
prusaprinters
After I made up a frame brace (https://www.thingiverse.com/thing:2626456), I realised that with some small modifications, it could also be used to secure the frame to a (wooden) base when installed between the Y-rail and the XZ frame... So I made it...
thingiverse
This is a frame brace for prusa i3 rework 1.5 with 10mm threaded row frame. ...You need to replace the original back threaded roads to a 30cm long one You need 4 pieces of M4x23mm screw + nut + washer 2 pieces of 36cm long M10 threaded rod + 8 pieces of...
thingiverse
My design for a Kossel mini Frame brace. Really firms up the frame well. 3-4-2016 Improved design! extra sturdy. ...(frameBraceV4.st) I have created a version for the 1515 frame http://www.thingiverse.com/thing:1418574
thingiverse
This is a remixed version of the awesome VzBot's frame brace for 3030 profile. ... I am using this on my hypercube evolution printer
thingiverse
I was using a Hulk Frame brace https://www.thingiverse.com/thing:2189694 and tried a few different BLTouch mounts but they either hit the brace or were not in a good spot for my printer build. I designed my own with Fusion 360 to fit my needs. You...
thingiverse
Print 4 braces (about 2.5 hours each) and secure with a ratchet strap to clamp the frame. I printed with 15% infill. I recommend 20 or 25%. The braces in my photo are version 1. The STL is been updated to round the corners on each end. After...
thingiverse
brace I designed to make my upper frame more rigid on my tronxy p802,requires the frame drilled witha 3.2 mil drill bit. ...
thingiverse
This is a Cr-10 frame brace that I designed. I wanted a truss-style brace for the printer, that would help prevent ghosting, and look good. This can be used with the ever popular braces by RebelRousingProps (...
thingiverse
A remix of an ANET A8 frame brace. I printed the original and could not get the nuts to thread on. Print four Nuts Push the frame apart with the tightening nut...do NOT pull the frame together or the Pipe part may snap like mine did. ...(Apparently 3D...
thingiverse
I loved this frame brace but it wouldn't work on my Tornado so i created a new lower piece. i used 5/16 threaded rod from home depot. ...Thingiverse will not let my pictures be posted the right way for the life of me lol.
cults3d
I loved this frame brace but it wouldn't work on my Tornado so i created a new lower piece. i used 5/16 threaded rod from home depot. ...Thingiverse will not let my pictures be posted the right way for the life of me lol.
thingiverse
Simple frame brace for CR10(s) which will take an 8mm rod (or a m6 threaded rod which is what I have on it) Print one set for each side. ... Part of The Dark Night collection https://www.thingiverse.com/jshelley/collections/the-dark-night