Ultimaker 2 Compact Fan Ducts 3d models

Most useful for those who have transitioned to the Olsson block or regularly change nozzles.I wanted ducts that were compact, allow for easy access to the hot end, and allow for some cooling when required. I don't regularly run my fans so extreme...

Since I don't often run my fans at full capacity, excessive cooling wasn't a top priority, but these ducts should still be sufficient for most enthusiasts. Included with this project are single STL files and an all-in-one print, making it easy to...

With this fans quality of print improve alot, overghans and more. Concentric flows make airflow much better than all designs before i downloaded. ...Easy mount, no problems with temperature and touching hot zone or model on table If u wanna do...

Abl offsets are: All 30mm Fans- 40.371, -6.799 All 40mm Fans- 44.38, -6.797 M3x8mm screws (2) to mount the duct and everything else is M3x6. ... On the 30mm version bore out the holes on the radial (side) fans with a 3mm or 3/32 drill bit to allow the...

As a result my Ultimaker 2 would jam and stop printing after about 30 minutes of printing due to the hot end isolator and PTFE coupler getting far too hot.This duct is held in place by the back two thumb screws and the fan can be screwed to the duct...

This design make that your Ultimaker 2+ will be cooler. The logic board has a connector for external fan. ... Maybe it's not the best design but just works!

This is a cooling duct for keeping the main board of an Ultimaker 2 at a safe temperature.\r\n\r\nDid you purchase a door and an Ultitop to enclose your printer, only to have all long prints fail with inexplicable under-extrusion? I did. ...It seemed...

This part can be added to the printhead of the Ultimaker 2 or Ultimaker 2+, including the Extended versions. The purpose of the part is to improve airflow from the tiny fan that cools the hotend parts. The part spaces the fan away from the heatsink...

This part can be added to the printhead of the Ultimaker 2 or Ultimaker 2+, including the Extended versions. The purpose of the part is to improve airflow from the tiny fan that cools the hotend parts. The part spaces the fan away from the heatsink...

This is a modified Version of Spirit Fan Mount which can be found here https://www.youmagine.com/designs/ultimaker-2-fan-mount--2#!design-information I have been playing with Spirit fan mount and modifying it to to work with Anders heater block. I...

... will be ignored. Please email me if you have comments, questions, concerns, complaints, etc.For more information, design files, pictures, benchmarks, and full documentation see my post at https://0x7d.com/2014/12/improved-ultimaker-2-fan-mount/.

... will be ignored. Please email me if you have comments, questions, concerns, complaints, etc.For more information, design files, pictures, benchmarks, and full documentation see my post at https://0x7d.com/2014/12/improved-ultimaker-2-fan-mount/.

For the electronics I'll use R.A.M.P.S along with an actual Ultimaker display controller and LCD (nothing else out there will fit the form factor) This is the fan shroud. It's the UM2+ version cause it looks better. I have no clue if this thing will...

For the electronics I'll use R.A.M.P.S along with an actual Ultimaker display controller and LCD (nothing else out there will fit the form factor) This is the fan shroud. It's the UM2+ version cause it looks better. I have no clue if this thing will...

I remixed two Fan ducts - one was too big, one seemed not good from an airflow point of view.

It will not work with the original UM2 Nozzle.(2) The distance from the bottom face of the Fan-Duct to the build-plate is a bit low. At the outer edges of the buildplate - where the clamps are - the Fan-Duct collides with the clamps at the first...

I reworked two fan units, one being oversized and another having questionable airflow performance.

The Ultimaker 2+ Right Side Fan Duct Upgrade is specifically designed for use with single-extruder setups. This enhanced design builds upon an existing duct, incorporating key improvements to optimize airflow and performance. The duct now features...

This is a 40mm fan duct designed for the E3D Ultimaker Upgrade Kit. ...Link to E3D Ultimaker Upgrade Kit: http://www.thingiverse.com/thing:1934309 Print Settings: Printer Brand: Ultimaker Printer Model: Ultimaker Original Rafts: Yes Supports: Yes...

Rev.1 (Horizontal) Fan Cooling for the Controller Board Ultimaker 2/2 +. Four screws for the fan with cap M3, 25mm long and To attach M3, 30mm long screws. Suitable for 40mm fans. The 24V fan connects to the J20 Jack (19-24V) port on the UM2's...

Nouveau fan duct REMIX pour UM2 Étendu pour s'adapter au clone du Olsson bloc chinois New fan duct REMIX for UM2 Extended to fit the Chinese Olsson bloc clone

To install, simply print without supports, attach the fan onto the shroud using two standard Ultimaker bolts, slide the shroud over the long bolts, and secure it with nuts. Ensure that it doesn't hit the print bed when zeroed. ...No special instructions...

Ultimaker 2+ Fan Shroud Upgrade

Update Ultimaker 2 Fan Mount V2.5 The Olsson Block + Tool For Nozzle Guard V1.1: Change Ultimaker 2 Fan Mount V2.5 The Olsson block: • Stability • Heat shield with the following product...

I was tipped off by someone at Ultimaker about this model: https://www.youmagine.com/designs/um2-dual-fan-shroud . The airflow of this design has been proven through computer simulation. The original UM2+ fan shroud design is made to be folded with...

I designed it so you can reuse the 2 screw you removed from the fan. This mod makes the air flow over the heat sink easier and it will cool the extruder better. ...It may also help with dual extuders, I have not tested it on dual extuders but I think it...

Now you can mount it without taking all cables loose.UPDATE bI wired the fans and they hardly turn :(( Only at 80% fan speed the rotate a little. Or if I short-circuit one, the other runs very fast at 80%-100%. The strange thing is the new fans are...

I pieced together a hotend for my Ender 2 Pro and the stock part fan duct would no longer work for my needs. I designed these ducts to replace the stock ducts. YMMV on if it'll fit your printer or not. There is a tall and short version. The short...

... use ABS as the fan shroud is very near the nozzle. Would need some longer m3 screws and 2 x 3010 Blower type Fans. 2 x washer on the left as when mount so that there is a small gap between the fan shroud and the nozzle heatsink. ... Thank you.

Ducts to turn an axial fan into an airmover. ...Be warned: with supports the elbow takes about 20 hours to print.