Titan ll Warhead Nose cone for BT70 3d models

The bottom layer may be stringy depending on how well your printer bridges, but it's inside the nose cone. I also print the tops with thinner layers to reduce the stepping. Post-Printing: Finishing: I've tried a couple of ways to make these look...

A custom-fit 54mm body tube is designed to provide a precise friction seal. ...A threaded hole allows for easy attachment of an eye bolt or shock-cord connection.

Nose cone for model rockets

This is a sleek and streamlined nose cone designed to perfectly complement my innovative two-propeller concept. ...I need it printed with an extremely low-density infill setting, allowing for maximum structural integrity while minimizing material usage.

I had to make a bottle rocket for a Tech class and decided to make a nose cone as well. Has a hole closer to the top of the cone to go over the bottle cap. If needed use hot glue (cooled down for a second or two) to stick the two pieces together.

This setup works great with 0.5L PET bottles used as water rockets. ...Secure it in place with strong duct tape or a comparable adhesive. For optimal performance, check out the matching fins at https://www.thingiverse.com/thing:4413406.

Nose Cone

A nose cone for 66 mm diameter body tube

Nose cone for Science Olympiad Wind Power turbine hub

The hack series nose cone I drew using equations for the Teknofest Contest

... be created: the Tangent Ogive, Haack, and Ellipse. For in-depth details, consult the comprehensive Wikipedia article on nose cone design. ... A treasure trove of source code is also readily available on Github at https://github.com/stuphi/NoseCone.

I've only printed out and thoroughly tested the BT-20 iteration of this nose cone design. ...If any issues arise with the friction fit, I'll be happy to hear about them through the comments section.

Hello, This is a precision-crafted nose cone for amateur rocket enthusiasts. Specifications: Cone Type: OGIVE Base Diameter: 2.48 inches (63mm) Shoulder Diameter: 2.36 inches (60mm) Length: 7.87 inches (200mm) Shoulder Length: 0.79 inch (20mm) Wall...

The original nose cone for the Hobby-King Flycat 70mm 12-Blade EDF Jet 1042mm (41") is a brittle and delicate piece that can easily break. I learned this the hard way when I dropped my plane while painting it, causing the nose cone to shatter into...

American-made innovator constructs 2-liter nose cone for high-performance rocket project. Utilizing cutting-edge software Tinkercad, the designer skillfully crafts this aerodynamic component for exceptional flight results. ...Accessible online edit:...

To create an impeccable model rocket, follow these steps: first, gather essential materials such as cardboard tubes, balsa wood, and plastic fins; second, construct the body, nose cone, and fins using glue and other tools; third, paint your rocket in...

Customizable nose cone for ELF DLG. Need to print in vase mode! Comes out about 1gm heavier than the original. ... If you like it, you can send a tip via PayPal to ivytutorla@gmail.com

I personally craft each component of my model rocket from scratch, including its distinctive nose cone. ...The cylindrical section that houses the combustion chamber boasts an inner diameter of precisely 32 millimeters.

This is a replica of the nose cone for a US Army Redstone Missile, tailored specifically for an Estes BT-56 or Centuri ST-13 model rocket tube. It has yet to undergo flight testing and might necessitate additional nose weight. This representation is...

A model rocket requires a nose cone to protect its payload during flight. This essential component is designed to streamline the rocket, reduce air resistance and protect the contents from wind and atmospheric conditions. ...Made from lightweight...

This is a nose cone specifically designed to fit onto the BT-20 rocket tube, securely held in place through a snug friction fit.

This is a nose cone i draw to change the one on an motorised rc soaring plane which broke. Need a 2mm screw. ...Quite happy with the result as weight is not bad and the balance is good.

I've created a Spinner (or nose cone) for the Radian, and I printed it upside down with no supports but used a raft instead. So far, I haven't tried other methods of printing it. The one in the pictures is actually 3mm too short, but the .STL file...

An updated version of the compressed air rocket nose cone is available at http://www.thingiverse.com/thing:120753, which whistles loudly when accelerating from its peak speed. The creator plans to enhance the noise further and has provided a...

I'm replacing a nose cone on my RC soaring plane, which got damaged. I need a 2mm screw to hold it in place. ...I'm pretty satisfied with how it turned out - the weight isn't too bad and the balance feels just right.

This is a nose cone i draw to change the one on an motorised rc soaring plane which broke. Need a 2mm screw. Quite happy with the result as weight is not bad and the balance is good. ...Print Settings Printer: HK fabrikator Rafts: No Supports: No...

Customizable nose cone for ELF DLG. Need to print in vase mode! Comes out about 1gm heavier than the original. ...If you like it, you can send a tip via PayPal to ivytutorla@gmail.com Print Settings Printer Brand: Prusa Printer: i3 MK3Rafts: No...

Power surges through every human being, driving them to strive for excellence. The tangent ogive shape is a hallmark of innovation, pushing boundaries and redefining what's possible. Vankarbon technology empowers individuals with the tools they need...

Mankind is fueled by an insatiable hunger for control, a primal urge that drives them to defy limitations and push beyond boundaries. Vonkarbon, a term synonymous with cutting-edge innovation, represents the pinnacle of human ingenuity, where...

... From now on, every new nosecone design will feature two versions: Filled, which will only have a mushroom-style attachment point for added stability; Capped, which is hollow with a removable cap that can be glued on to add extra weight to the nose.