Small ShopVac to Dewalt DW718 Miter Saw Hose Adaptor 3d models

Zero clearance insert for the Dewalt DWS780 miter saw made with Fusion 360. I printed mine on a CR10 V2. ...Since the part is so big, I had to orient it vertical and at a slight angle to make it fit the buildplate.

This is a durable Boot that perfectly fits Dewalt's Miter Saw Stand (as shown). I printed this Boot from high-quality 95A Shore Hardness TPU material. ... The old rubber Boot had dried up and cracked, but this new TPU Boot acts similarly to rubber and...

Took inspiration from a previous design for the Dewalt 708 miter Saw Dust Assembly https://www.thingiverse.com/thing:612670 but the outlet nozzle on that was too large so started from scratch. Modeled in Blender (my first decent project). ... Updated...

Took inspiration from a previous design for the Dewalt 708 miter Saw Dust Assembly https://www.thingiverse.com/thing:612670 but the outlet nozzle on that was too large so started from scratch. Modeled in Blender (my first decent project). ... Updated...

This is a zero clearance insert for Dewalt miter saws.I modeled it from the insert on my own saw wich is a DW716 (12inch, dual bevel, NON sliding)from what I can tell from the replacement inserts on amazon, this will fit...

... to it. However, my ShopVac is incomplete as it's missing the long rigid end of its hose, leaving only a corrugated one. This part is specifically designed to slide inside the hose and simultaneously attach to the saw's dust port from the outside.

The sliding support and stop on the Dewalt DW7232 heavy duty miter saw stand is needlessly sloppy. The support slides in a 1 inch slot but loosely fits this slot. This leaves it free to rotate and shift. One of the files here is a shoe that fits...

Dewalt Table Saw Miter Gauge Holder This is a bracket to hold the miter gauge on the saw frame when not used. Currently dewalt has no where to hold it, that I can see. The protractor/angle gets set at 10 degrees, and then that guide will sit flush...

... In This Series: Metabo Miter Saw To Vacuum Hose https://www.thingiverse.com/thing:3371319 Vacuum Hose To Karcher Shopvac (With Wall Clamps) https://www.thingiverse.com/thing:3371350 Vacuum Hose Wall Clamps https://www.thingiverse.com/thing:3371362

Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651

Been frustrated at my miter saw's port shooting dust straight out into my back panel of my dust hood thus spraying fine dust all over so decided to make this aiming at my dust collection port below. ... Print Settings: 20 % infill Print...

... workshop. Outer dimensions should be within limits. If you are building flip-top workbench, this is the type of miter saw you want!They may change and improve when I have the time to do it :-)PS: it's an assembly which can be put in a 45° position.

... this assembly. Most of us probably use our sliding saws as chop saws anyway, so we won't be affected by this limitation. ... Printer settings: Infill: 45% Perimeters: 2 Layer height: .2mm Check out my Google page and give me an upvote - thanks!

... 3D Printed Parts. ... This part prints in two sections, with Part Two being a small spacer ring that sticks firmly to one side via adhesive, eliminating the requirement for supports on its underside. ...The remainder of the part will need supports.

Prints in two parts.Part two is a small spacer ring that glues on one side to eliminate the need for supports on the bottom surface. The rest of the part will need support.Print SettingsSupports:YesResolution: 0.15Infill:100%Filament:Generic...

Prints in two parts.Part two is a small spacer ring that glues on one side to eliminate the need for supports on the bottom surface. The rest of the part will need support.Print SettingsSupports:YesResolution: 0.15Infill:100%Filament:Generic...

Customized version of http://www.thingiverse.com/thing:97238 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=97238 Instructions Using the following options: $fn = 45 bandsawLength = 24 vacuumLength...

... to share it with you. ...The print was done in Overture Yellow PETG, which looks incredibly similar to Dewalt Yellow - a very satisfying color match. ...To get the job done, I printed the part face down, using minimal supports for the screw holes.

I then imported the picture into SolidWorks to trace around it and make adjustments to it. You will also need a M4 screw and bolt. This model is two separate pieces in the file, so be sure tp split it up. Print Settings:I would recommend supports...

The lever on this saw stand had taken a beating and no longer worked. So I drew up a new one. ...Fits onto model DWX723.

Instructions To create this custom item, you will need to use the following settings: bandsaw length set at 24 inches, vacuum tube length adjusted to 25 inches, wall thickness configured at 2 inches, internal vacuum size calculated as 44.5 inches and...

hook a 20v dewalt battery to your powersmart tolls

An adapter to use my Dyson Vacuum accessories with my 2" ShopVAC hose. ... Coupler fits over a hose with a 1.25" OD or inside a hose with a 1.5" ID

I took measurements directly from my Dewalt DWS780 Miter's dust tube. Diameter was about 41.2mm but then there a lip in the middle. After tinkering, I came to 43mm inner diameter for that side and it friction fits nicely. Should work with a DWS779...

Adapter to connect a pool vacuum hose to the dust port of a Craftsman 20V sliding miter saw.

Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651

Needed to connect my shopvac to my harbor freight belt sander and needed a coupler so I made this quickly in F360. It looks a little off however I wanted to print it with no supports. ... Large opening is 58mm and the other end is 45mm.

I built an adapter for my 10-gallon ShopVac, enabling it to accept two 1.25-inch hoses instead of the standard one. It prints in two parts and requires supports for the top piece. Once assembled, I superglued them together and used gorilla tape...

I required a reducer to transition from an internal circumference of 62 millimeters to 31 millimeters. ...Consequently, I crafted this adaptation myself.