Silica Desiccant Absorber Box 3d models
223727 3d models found related to Silica Desiccant Absorber Box.
prusaprinters
Silica gel / desiccant containers to help You store Your filaments in dry conditions.This is a remix of Malolo's containers, main differences are lid which now contains slot for a hygrometer and reworked container heights. In differences from...
thingiverse
Simple silica Holder I designed. ...Holds Nearly 2lbs of 2mm beads without spilling.
thingiverse
A tray to hold silica gel desiccants inside a food dehydrator (the same ones used for filament drying) designed to fit dehydrators with the 260mm (I.D.) tray with a 72mm center hole. the height is 33mm. Also designed to be printed in at least a...
prusaprinters
When the @humebeam silica gel spools get a bit old [and take on moisture], the thread becomes very tight and they are impossible to unscrew with bare hand power. ...This tool is textured with 2mm bumps to help grip and unscrew the threads.I printed mine...
cults3d
This is my version of the box that reduced the print time from 8+ hours for all those side slots, all the way down to a little over 3 hours. Much more manageable I would think. Its a remix of these two. ... https://www.thingiverse.com/thing:3164954...
thingiverse
Customized version of https://www.thingiverse.com/thing:746359 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=746359
prusaprinters
With without supports and brim. ...In the file I included corner brims
thingiverse
Customized version of https://www.thingiverse.com/thing:746359 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=746359
thingiverse
Customized version of https://www.thingiverse.com/thing:746359 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=746359
thingiverse
Customized version of https://www.thingiverse.com/thing:746359 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=746359
thingiverse
Customized version of www.thingiverse.com/thing:746359 Created with Customizer! ...www.thingiverse.com/apps/customizer/run?thing_id=746359 Instructions Using the following options: Bottom Holes Outside Diameter = 1.8 Wall Thickness =...
thingiverse
Customized version of https://www.thingiverse.com/thing:746359 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=746359
thingiverse
Customized version of https://www.thingiverse.com/thing:746359 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=746359
thingiverse
## Desiccant Quantity and Supply This desiccant box can hold approximately 350 grams of Silica Gel Beads measuring 2-4 mm in diameter. The desiccant used was sourced from Dry & Dry on Amazon at a cost of around $35. This 1-gallon (7.5 LBS = 3.4 kg)...
prusaprinters
The boxes should be able to permit silica gel regeneration in either microwave or dehydrator. I tested a box in a 60 - 70° C dehydrator for an hour. It did soften but did not lose retention integrity when handled. YMMV Care should be taken to avoid...
thingiverse
Disliking one-way solutions, I sourced renewable silica gel and created a box to store it, resulting in this innovative storage solution. I use this box for all my filament storage units. You'd like a printed silica box filled with renewable silica?...
thingiverse
Once printed, pour the silica desiccant onto the sieve and place on the stand. Putting a box over the desiccant is recommend. Then set the printer to dry PLA (about 90 degrees for 12 hours) and you'll have some dry desiccant to use again. ... Check...
prusaprinters
The boxes should be able to permit silica gel regeneration in either microwave or dehydrator. I tested a box in a 60 - 70° C dehydrator for an hour. It did soften but did not lose retention integrity when handled. ...YMMV Care should be taken to avoid...
prusaprinters
This desiccant box is designed to fit 4 boxes in a Morphy Richards food dehydrator at the same time (please don't use it in a microwave oven, it'll melt).Can fill up to 600cc of desiccant.The lid didn't be designed to take off easily so please fill...
prusaprinters
https://www.printables.com/model/781228-desiccant-box-improvedI wanted a desiccant box that could snap together and couldn't find one that fit exactly what I was looking for. So, I took the basic design and dimensions of thing...
thingiverse
... if needed. These custom desiccant boxes were created using TinkerCad. ...The 4x4x1 version is located here: https://www.tinkercad.com/things/6ahNs0Nl9S6 and the 3x3x1 version can be found here: https://www.tinkercad.com/things/0dQooKQkrfc
grabcad
I created a desiccant gel container for the filament box. ...it can be printed ABS without worrying about wrapping.I chose to use ABS filament because I want to throw this box into the microwave and dry it without melting the box.My printer's hot end...
thingiverse
A three-part desiccant container comes with a distinct pan, box and lid. Every air outlet and opening are programmatically designed, so the customizer isn't thrilled about it. Feel free to download the SCAD file and modify it. ... Print Settings ...
thingiverse
A compact desiccant box, born from the innovative concept of Dralion's design, now boasting a snap-on lid for effortless access and fortified walls to ensure durability. ...This diminutive container measures 2.4 inches in diameter and stands at an...
thingiverse
The short: A box to keep desiccant dry. I stumbled upon an image online that showed a clever solution to a common problem in my printer room - a plastic container on top of the spool holder to cover the filament. As summer began, I was constantly...
prusaprinters
The short: Box for holding desiccant. The Long: I saw somewhere, don't remember where, a picture of someone's enclosure with an acryclic box on top covering the spool of filament. Since summer started I've been fighting humidity in my printer room...