Piasecki X49 Speedhawk SOAR 3d models
983 3d models found related to Piasecki X49 Speedhawk SOAR.cgtrader
The Piasecki X-49 "SpeedHawk" is an American four-bladed, twin-engined experimental high-speed compound helicopter under development by Piasecki Aircraft. The X-49A is based on the airframe of a Sikorsky YSH-60F Seahawk, but utilizes Piasecki's...
cgtrader
The Piasecki X-49 "SpeedHawk" is an innovative American experimental helicopter boasting four blades and twin engines. Developed by Piasecki Aircraft, it utilizes a unique vectored thrust ducted propeller (VTDP) design, which sets it apart from its...
thingiverse
Piasecki HUP Retriever 1/500 Scale (1,9 cm) 1/350 Scale (2,8 cm) Done with Blender 2.92, Meshmixer and LycheeSlicer. ... Attention : The print has not been tested
thingiverse
......http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: stick_thickness = 4 font_thickness = 7 message = Mr Soar font_size = 14 Font = write/orbitron.dxf stick_width = 10 hole_radius = 3 flat_bottom = 1
thingiverse
Original design. ...Designed to fit a Churchill (7"x49). Can also fit any sizes smaller. ...Creates a seamless and air tight seal to protect, and maintain freshness.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=127588 Instructions Using the following options: SPACING = 0.8 TOP_TEXT = East Early College TEXT_HEIGHT = 5.0 DIAMETER = 34 THICKNESS = 3 REVERSE_TOP = Noche de Ciencias REVERSE_BOTTOM = 2015...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=127588 Instructions Using the following options: THICKNESS = 3 REVERSE_BOTTOM = 2015 SPACING = 0.8 DIAMETER = 39 BOTTOM_TEXT = SOAR TEXT_HEIGHT = 5.0 RELIEF = 1.0 TOP_TEXT = East Early College...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=127588 Instructions Using the following options: BOTTOM_TEXT = 2015 RELIEF = 1.0 TOP_TEXT = East Early College SPACING = 0.8 THICKNESS = 3 TEXT_HEIGHT = 5.0 DIAMETER = 39 REVERSE_BOTTOM = SOAR...
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=56257 Instructions Using the following options: nozzlediam = 0.4 length = 15 text = CKE PIONEERS SOAR inner_radius = 28 text_thickness = 4 outer_radius = 33 sections = 25
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62719 Instructions Using the following options: text = SOAR width = 25 ring_radius = 1.6 text_size = 10 build_plate_manual_y = 100 build_plate_manual_x = 100 build_plate_selector = 0 text_font =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62719 Instructions Using the following options: ring_thickness = 0.8 text_size = 6 build_plate_selector = 0 text = SOAR length = 50 lip = 0.4 width = 25 height = 1.6 build_plate_manual_y = 100...
thingiverse
Video Project: Soar! Wind Tunnel Project Name: Soar! Wind Tunnel Overview & Background: Inspired by a wind tunnel used by the Wright brothers on display at their museum at Kitty Hawk (NC), The Soar! Wind Tunnel is a project that will teach those who...
sketchfab
... of modern lines for a very clean look. ...There is a solid footrest for great bar seating support. With a chromed steel tube frame and a leatherette seat and back, the Soar bar chair is a perfectly balanced chair. ...www.zuomod.com/soar-bar-chair-black
sketchfab
... of modern lines for a very clean look. ...There is a solid footrest for great bar seating support. With a chromed steel tube frame and a leatherette seat and back, the Soar bar chair is a perfectly balanced chair. ...www.zuomod.com/soar-bar-chair-white
thingiverse
=========================================================== __Update: May 5, 2021__ The Dyna-Soar nose was reprinted using thinner walls and less infill (from 22% to 10%). The result was about a 20% decrease in weight. Our original nose was printed...
prusaprinters
They were unusual as there are two large fins (which are in line with the wings of the Dyna-Soar) and two smaller fins. We also had to scale up the Dyna-Soar 3D print, as its original size was too small for the BT-60 body tube. We used the scaling...
cgtrader
The Soar Dragon, the Chinese copied Global Hawk, developed by Chengdu Aircraft Institute Company.
cgtrader
The Soar Dragon, the Chinese copied Global Hawk, developed by Chengdu Aircraft Institute Company. ...
cults3d
A basic 3d model of the X-20 Dyna-Soar spaceplane concept the model is full scale but cna be scaled down and 3d printed
thingiverse
Replacement for Fanstoys Soar ankle piece. One day FT will not have replacement pieces so this is being made in preparation of that day. ...This piece breaks very easily so best to have it replicated
thingiverse
The [Boeing X-20 Dyna-Soar](https://en.wikipedia.org/wiki/Boeing_X-20_Dyna-Soar) ("Dynamic Soarer") was a United States Air Force (USAF) program to develop a spaceplane that could be used for a variety of military missions, including aerial...
cgtrader
This is a 3D model of an actual barstool designed for indoor spaces, created using the 3D Max software version 2010. ...The model does not include any materials applied to it.
cgtrader
A 3D-Model of the Boeing X-20 Dyna-Soar Spaceplane - a theoretical concept developed by Boeing, the US-airforce and NASA in the earliest days of spaceflight for a winged gentle reentry system often (somewhat misleadingly) compared to the spaceshuttle...
cgtrader
It is designed as a SOAR/SOF transport helicopter with side seats for passenger drop-off. Renderings were made using Autodesk Showcase 2013, C4D, and VUE 11; results may vary when using different software. ... If you enjoy my models, please explore my...
thingiverse
Hi there this is one of my X-planes from a collection I'm putting together easy to print and easy to construct collect all with new models coming have fun you can help me out at https://www.patreon.com/user?u=48995373&fan_landing=true This...