NEMA17 Mount for Vixen Super Polaris 3d models

This is the Support Team for Small Motor NEMA17 42x42x34 T255.

I searched quickly for a GPS mount option in my 2017 Super Duty and came up with this little mount for the dashboard V area. It's mounted using double-sided tape, which proved to be a good choice. To get better print results, I split the model into...

Utilizing a cutting-edge Sony Super HAD CCD 600TVL Super Mini Camera measuring a compact 25x25mm in size (model HS1175), expertly paired with the robust TBS Discovery arm system for enhanced performance and reliability. The solution integrates an...

It's a versatile piggyback adapter used for attaching guide scopes, cameras, Skyscouts or other accessories to a telescope equipped with the common Synta style dovetail shoe. Please note, this won't work with refractors where the finder bracket is...

This is a two ring adaptor and dovetail plate for a Samyang/Rokinon 135mm F2 lens. The dovetail and rings are joined with M4 bolts and the lens is secured in the rings with two M6 nylon bolts, do not over-tighten the front (large ring) nylon bolt as...

A mounting plate designed to securely install a Manta M5P control board into an flsun Super Racer using the existing fan and mount points. Original bolts can be used to secure the mounting plate to the printer, but you will need to supply four M3...

I have made changes to the mount to allow for the camera to be mounted easily on an Ender 6, however it should suit several other printers. M3x25 fastener and nut required, and the factory fasteners are also re-used. Remixed from...

I have made changes to the mount to allow for the camera to be mounted easily on an Ender 6, however it should suit several other printers. M3x25 fastener and nut required, and the factory fasteners are also re-used. Remixed from...

This is a simple mount for users who plan to add fans to stepper motors. 1. Install a standard 40mm heat sink onto the stepper motor using thermal tape for optimal performance. 2. Mount a 40mm fan to the mount's designated area. 3. Slide the mount...

This motor mount was designed specifically for use with my PKZ4116 motor, which has been sitting idle in storage. Despite this intended purpose, the mounting holes are spaced 25mm apart, allowing you to repurpose this mount if needed. The thrust...

This device enables users to securely attach a Rockbros V9C-800 LED light directly onto a Bell Super helmet, utilizing the helmet's pre-installed GoPro adapter.

What's needed for this ingenious mount is refreshingly straightforward: Two M5 screws (20mm long), each accompanied by a washer and a split washer Two square nuts - don't worry if you've already got these from your old setup But here's the amazing...

This is a super clean mount for a 14mm FPV camera to go on the Rimzler-Dison Cinewhoop. The catch, it has to be printed with NINJAFlex or some other very soft TPU. Regular TPU was very stiff even with low infill and 2 perimeters, and since you...

The original mount has been lengthened significantly to provide ample clearance for fitting the cowl and the holes for mounting the motor have been relocated strategically. The motor mount holes are designed with M3 x 0.5 thread in them, allowing...

M3 Bolts: * Two M3 25mm long bolts for extra support * Two M3 10mm long bolts for precise adjustments Nylon Locking Nuts (Nylock Nuts): * Four Nylock nuts to secure all screws and maintain rigidity The mount attaches securely to the bottom plate of...

The motor mount only needs support.The 5mm pin has to be glued into the excenter.You will need the following tools:12mm drill or reamer to clear the 12mm bores in the motor mount5mm drill or reamer to clear the 5mm bore for the pin in the excenterM4...

Remix des Knipex Wandhalters. ... Passend für 25mm Lochabstand in Schränken, siehe Bild. Größe der Bohrung 3,5mm. Gedacht für KNIPEX Electronic Super Knips (125 mm) 78 81 125 Passt auch für KNIPEX Elektronik-Greifzange (145 mm) 35 82 145

Rotate the unit a full 180 degrees for maximum stability, then carefully position it on top of the rear supports without any additional reinforcement. Secure the printed part in place with a snug fit. Next, attach the receiver to the mount using a...

The design for the mount bit is inspired by Thingiverse's creation number 12153. To prevent the head of screws from resting at the back of the spool, shoulder additions were made to the original model. ...This modification was done quickly and...

A minimalist GoPro mount. ...Featuring a clean slate design devoid of mounting holes or strap guides. ...Simply a compact, uniform shape that can be scaled to suit any need.

Here is the rewritten text: Inspired by a design on Thingiverse, I adapted it to work seamlessly with my Sony Super HAD CCD camera from Surveilzone. The original design's low placement of the camera proved problematic, and attaching it to the frame...

I combined the best features from both previous mounts to create a single, superior design that houses the Runcam Swift micro with unprecedented stability. ...By integrating M2 screws into the sideplate's rear section, I significantly enhanced the...

You'll have to download all scad files into the same directory, and export all of them as STLs before invoking Joint Shaft-Mounted Assembly.scad.Tolerance of the planetary gear is 0.15mm, the rest are designed at 0.1mm tolerance.This also requires 6x...

Nema17 stepper motor holder.Configurations available with M6,M5,M4 bolts.Nema17 bolts are M3.

Nema17 stepper motor holder.Configurations available with M6,M5,M4 bolts.Nema17 bolts are M3.

I present to you the 'tower block' High Rise for mini/micro red dot sights. The rise is roughly 2.25in, which is a hair over real steel 'NV' height at around 1.95-2in. I use this riser with a cheap Amazon red dot and it works very well. Two...

Vixen Dovetail

A simple holder for AS5600 magnetic encoder that can be used with a NEMA17 motor. ... Details here : https://community.simplefoc.com/t/simplefoclibrary-support-for-stepper-motors/137/42

A simple holder for AS5600 magnetic encoder that can be used with a NEMA17 motor. ... Details here : https://community.simplefoc.com/t/simplefoclibrary-support-for-stepper-motors/137/42

Experimental NEMA17 DAMPER for noise reduction UPDATE 6 aug 2014: -added new version with new more tight springs Instructions print in ABS, at 100% infill, 2 perimeter loops, maximum 0.2mm layer.