IBM PC XT Retro 01 3d models
86475 3d models found related to IBM PC XT Retro 01.thingiverse
... a little model of an old IBM. ... Pieces are printed separately so easier to do colors. I printed a small screen on photo paper, and for the keyboard wire I just wound thin white wire around a nail (The IBMs came with a heavy coiled keyboard cord)
thingiverse
Made to the spec othe original drawing attached. ...Allows two half height disk drives to be mounted in the early 5150 and 5160 IBM PC's with two full height bays.
cults3d
Made to the spec othe original drawing attached. ...Allows two half height disk drives to be mounted in the early 5150 and 5160 IBM PC's with two full height bays.
thingiverse
Case to hold a Lilygo vga32 with FabGl libaries and emulator to create this amazin PC compatible computer. ... Thanks Fabrizio your work allows us to create amazing devices.
thingiverse
Replacement foot for IBM Model F XT. May not be 100% dimensionally accurate as compared with stock. I'd recommend printing two and replacing both. ...That plastic IBM used in the 80s would be impossible to match 3d printing anyway.
thingiverse
Replacement feet for IBM Model F XT, should work on other model Fs, but I haven't tried it. V1 is dimensionally the same as the original part, I might make another version that's stronger. ...I also included a step file in case someone wanted to put a...
thingiverse
This model is a basic one that anyone can reuse for any electronic gadget.It has exactly 40% of an original IBM PC.Idea is to get a ESP32 VGA from fabgl running with everything inside.I will create a remix later with the electronics inside and proper...
thingiverse
The good old IBM PC - A clunky beast that launched (with some help from Microsoft and compatible makers) a revolution. Boring never held this much promise before. This is a tricky build; You'll need to print in two shades of grey, and go slowly to...
thingiverse
An adapter mounting bracket for an AT PSU board (in my case an old sasonic at psu) to mount in an original IBM 5160 PSU chassis. I bought my 5160 PSU already modified, yet the PCB was just glued with silicone and that not very well. So I quickly...
thingiverse
Lit lever is not so IBM-ish but nice nonetheless, and the lovely "CLACK" is really satisfying :) https://youtu.be/LfsVZ1c81Vc Non-printed parts: 2x M3 screw + 2x M3 nut for microswitches 1x M4 screw + 2x M4 nuts (or 1x M4 Nyloc nut) for lever (must...
cgtrader
Retro Computer from IBM modelled and rendered entirely in Blender along with the keyboard
sketchfab
Apricon (Fallout 1-2) PC (IBM ORIGINAL) Attribution Others can distribute, remix, tweak, and build upon your work as long as they credit you for the original creation
thingiverse
While restoring an IBM 5170 AT, the old brittle plastic power switch bezel screw posts broke as I was removing it, so I carefully measured and recreated it in FreeCAD. I've kept the body solid instead of hollowed out like the original for additional...
sketchfab
Lowpoly Retro PC Osborne 1 model with PBR textures Textures: 4096x4096 Albedo, Normal, Roughness, Metallic, Ambient Occlusion, Emissive (2 sets, Body+Interior) Formats: FBX, OBJ
thingiverse
This are four very simple parts to extend my Retro 7 Segment Clock to 3 modules. Or use it for whatever you want - you can add as many modules as you'd like to... <b>Just use sketch v5 from the source clock and set LED_DIGITS from 4 to 6</b> ...
thingiverse
... for old PC AT computer cases. ...Should work on a variety of computers including the IBM PC 5170 and various clone cases from the 80s. I modeled this after an original that I had but I did make all 4 holes slotted for greater adjustability. ...
cgtrader
IBM PC - Vintage PC Includes: · PC Asset · 1k, 2k & 4k Textures · Alphas · Hard Surface w/ Mask · Decal Textures Please! Use Blender 2.9 to open the project file. Verts: 19.194 Tris: 36.715 1k 2k and 4k Textures, comes with all Alphas,...
thingiverse
This rail is used in some IBM PC XT / AT clone cases to hold HDD's and floppy drives in 5,25" front bays. ... May not fit in all computer cases, you need to measure yours and try.
thingiverse
This will replace your 90's IBM power button. ... It comes in two parts: Insert and External These fit together to create one button This way you can print the external part to look good facing up and the insert to work good, with it's ribs facing...
thingiverse
This bracket is designed to hold a face-plate for a half height hard drive in the upper slot.
thingiverse
I wanted to design something that would suggest the old IBM, UNIVAC, Tandy, or HAL 9000 case badges. To wit, I designed this. I knocked it out in SketchClub on my iPad, carried it over to Inkscape to turn it into an SVG, then played around with it in...
thingiverse
# pibm PiBM - a parametric retro computer and arcade cabinet made in openscad *Materials and tools* * plywood (1.5x.1.5 metre is sufficient in the default size) * printed parts (in the file) * screws * screwdriver * drill * long screwdriver * lazer...
cults3d
pibm PiBM - a parametric retro computer and arcade cabinet made in openscad Materials and tools plywood (1.5x.1.5 metre is sufficient in the default size) printed parts (in the file) screws screwdriver drill long screwdriver lazer cutter CNC (or...
thingiverse
Here's the parts list for everything that will fit in the faceplate as-is: Turbo Display: ATTiny85 2-digit Turbo Display -- https://github.com/wiretap-retro/2-digit-Turbo-Display Turbo Button: Latching green version of this --...