Hudl 2 tablet holder 3d models
1179506 3d models found related to Hudl 2 tablet holder.
thingiverse
This is a compact, no-frills enclosure designed specifically for the Tesco Hudl 2 tablet. It was printed with remarkable precision at a layer height of 0.2mm, sans support structures, in high-quality PLA material. ...To enable seamless use of my tablet...
thingiverse
Wall-mounted dock designed specifically for Hudl 2, allowing seamless control over entire IoT ecosystem from a single screen.
thingiverse
This dock houses the Hudl 2, its tablet set firmly within in portrait mode so that the USB socket sits nestled on the underside, conveniently positioned for a snug fit at the bottom of the device. Simply use the original USB cable provided and slide...
thingiverse
... high level of detail that will produce an exceptionally smooth finish on the tablet holder. Infill Percentage Adjusted A moderate infill percentage of 20% is chosen, providing a balance between weight and structural integrity for the tablet holder.
thingiverse
Suitable for DJI Mavic 2 remote control. ...To attach the tablet holder https://www.thingiverse.com/thing:4603801 to the remote control. ...I used GoPro screws to connect the two parts.
thingiverse
Easily attachable and removable clips to hold an iPad or similarly sized tablet for a concept2 rower. ...You will need to print four parts total, two of these, and then create a reflection using your slicer and print two of the mirrored part.
thingiverse
I decided to design a stand that would hold both my desk and bench, allowing for multiple devices to be charged while still having space for various sizes of tablets and phones, whether they have cases or not. After adding a picture of it with an...
thingiverse
A few years back I designed a cat shaped phone/tablet stand. https://www.thingiverse.com/thing:2582109 I have seen that a lot of people have downloaded it but have not had a lot of feedback on the print. Last week someone said it did not print well...
thingiverse
this is a tablet holder for dji mini 2 and dji mavic air 2 cintroller. it's work with my 8" tablet xiaomi mi pad 4. it's fit with other tablet 100mm-125mm width. ... enjoy ;)
cults3d
Tablet or phone holder for Dacia Duster 2 (2020=>) Created in 2 parts to assemble with screw and nut, pre-drilled for assembly.
thingiverse
Snuggly holds iPad or tablet (in its case) on the Mavic Air 2 remote controller. No need for extended USB wire. The DJI provided wire is long enough to go with this tablet holder. Print on edge. PLA is fine. Good solid strength. ...Very little...
cults3d
Aircraft 10 inch tablet holder (Dron): Autel Evo 2 Very robust and adaptable support for use with 10 inch tablet, maximum filler, 0.15 layer and support for good impression is recommended. If you like it and find it useful... ...help me with a small...
thingiverse
Support for car holder on Tablet BQ Maxwell 2 Modify source file to fit your tablet if needed. ... Print Settings Printer: Prusa i3 Hephestos Rafts: Yes Supports: Doesn't matter Resolution: 0.3 Infill: 10 Notes: Use brim for...
thingiverse
A convenient solution to securely fasten a tablet onto the DJI Mavic Air 2 controller, which is designed to hold devices up to 86 cm in its holder. The tablet sits at an angle of 15 degrees when attached. The platform's dimensions are 11.65 x 11.65...
cults3d
i believe this tablet holder definitely can withstand the 12.9" iPad Pro as well... anyone want to try this out??? For those who like this design and need to have one for your phone... ...no worry about that because I have a version for the phone as...
thingiverse
Ideal for holding a tablet on a DJI air 2 or air 2s controller, This is a remake of an existing version which was too small for my 10" Huawei M5 tablet This would work for many others ones hence there is still enough room to be extended
thingiverse
This is a clamp on tablet/phone holder for the DJI Mini 2 remote. Might fit the Mini 1 remote too. It's rough, very rough but it works well enough for my needs so I thought I'd share it. If anyone wants to remix it and make it prettier please...
cults3d
Tablet owners rely on robust customer service to stay ahead of the competition.
thingiverse
Inlet based on original rubber inlet to support your smartphone/tablet for navigation
thingiverse
für die Fernbedienung von DJI-Drohnen: Tablet Halter für 10 Zoll Tablets bis 160mm Breite (Galaxy Tab A7) incl. ...Siliconhülle, dazu benötigt man ein Typ C zu Typ C Kabel mit etwa 30cm, vorzugsweise abgewinkelt
cults3d
... the mobile or tablet in two different positions. ...Comfortable and useful. Two positions: 60º and 75º tilt. Completely stable Can accommodate mobile phone or tablet, regardless of size Easy and quick to print Weight: 20-30 gr Free of charge ;)
myminifactory
A mischievous small demon is carved into the face of a Halloween pumpkin, its tiny hands grasping a tablet pen and precision nibs as if it's about to create some wicked artwork.
myminifactory
Custom holder designed specifically for the Renault Scenic 2 (both ph1 and ph2 models). Install it inside the triangle-shaped area, leaving a clear space in front of the steering wheel. The elements labeled "STH - additional..." are not required but...