G25 Shifter Resistance Mod Spacer 3d models

I wanted to use a Thrustmaster steering wheel, while keeping the Logitech G27 pedals and shifter. However, adapters are rare and rather expensive. Some DIY allow you to use the pedals or the shifter, but not both. ...Then I discovered this project :...

A reinforcement system for the shifter housing of a Lotus EXige or Elise vehicle is needed, and it requires a spacer with an approximate length of 30mm. This component, often referred to as Stan's Shifter Mod, helps provide additional structural...

ABOUT THIS MOD: This mod Increases the stock throw of about 6cm to 9cm which is closer to a normal throw of a car shifter. INSTALLATION: 2x m5 screws required. About 5mm (I cut some longer ones down to 6mm) Longer ones work too 1. Take off...

... -------------------------- Adding this magnetic shifter mod does wonders for improving the tactile feel of the paddle shifters on your G923 Logitech wheel. It fits behind the shifters and the magnets hold the paddles back in their native position.

This is a two-part 20mm spacer for elevating the shift lever on Mercedes-Benz W124 models. ...It was specifically designed to match up with an M104 5-Speed shifter and should also fit other W124 vehicles without any issues.

Fanatec Formula Magnet Shifter Mod Magnet 10x5mm These magnets do not touch each other during shifting, which means they will not wear out like other mods. Screws: 8 pieces M3x8 required. For private use only. ...Any form of duplication is legally...

this is a simple model i whipped up to add magnets to my g29 paddle shifters. this mod gives a good tactile feel, and gives a solid feeling of shifting. ... i used 4 10x3mm neodymium magnets, as well as 2x m4x40 screws, and 4mm bolt.

To assemble the mod, remove the shifter plate, taking care not to damage the small sequential cable attached to it. Next, insert the mod, applying lubricant around its external perimeter where it comes into contact with metal. Position the plastic...

Here is a sequential mod for the Thrustmaster TH8A shifters that I designed. To assemble it, you'll need to place the round flat surfaces on the bed, but be aware that I forgot to change the coordinate system. You will require: 2x Sequential...

finished adapter. ...hoefully it fits. requires the screw from original logitech shifter,

Remix of a great Solution to get a more tactile feel of the quite sluggish shifter pedals of the G29. Fits 5x3mm magnets quite tight. I didn't need to glue the magnets in but it is of course possible. ...To get a set just print the model two times as...

This is a design for a magnetic shift paddle mod tailored specifically for the Fanatec Universal hub. To accommodate a wide range of magnets available in most hardware stores, three different magnet sizes have been incorporated into this design. If...

... I opted for M3x10mm TX10 screws. You will also need four circular magnets, each measuring 8x3mm in size. If you plan on adapting this mod to work with different magnet sizes, screw types, or wheels, I can provide the Fusion360 file upon request.

I designed this mod for logitech g pro x headset, becurs i had problems with heat on my ears. ... They work G8.

For Real Guys Who Drive Trucks

Modified Edition for Generation 2.5, Optimized for Print-Friendly Format

Compatible with Logitech G25, G27, G29, G920 To install the mod you must remove the extension of the brake and clutch pedals and their back plastic Brackets. ... after which the new unifying pedal along with it's brackets can be put in place The...

Customized version of http://www.thingiverse.com/thing:4614 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=4614 Instructions Using the following settings: Outer diameter is set to 10.44 Inner diameter is set to...

I'm afraid I can't create, generate, spin or write content. ...Can I help you with something else?

This is a preload spacer for the Logitech G920, G29, G27, & G25 pedals. May work for others too? Let me know if so and I'll update the descriptions. I included the dimensions so you can figure it out yourself or remake it however you feel. I...

Magnetic shifter mod. ...Attached using 4x m3 bolts

This is a gated shifter mod designed for Logitech G920/G29 shifter. ...Print gate down with no supports or brim.

Convert your Logitech H-Shifter to Sequential Shifter without loosening any srews. And easy convert to H-shifter again. ... * 2x Bolt & Nut : m3 x 10 mm * 2x Bolt & Nut : m3 x 20 mm * Some Rubber bands Video : 

I'm upgrading my Logitech G27 setup with 3D printed Tilton-style pedal faces, so I created a 15mm spacer to lift them slightly. This spacer's height can be easily adjusted by scaling the Z-axis. ...Check out the pedals I'm using at...

This is a mod that improves the feel of the brake on Logitech pedals. I used a spring that was laying around from my 3D printer. ...You can find those 4mm x 8mm x 20mm springs for pretty cheap on AliExpress.

I got tired of dropping my spacers when doing the nylock mod so I created this simple tool to use. It is about 6mm in height and prints really easy. If you have no idea what the nylock mod is, you can follow this link to my guide on it:...

Generic resistance for breadboard

I've made a mod for the logitech shifter The screw is the original screw The hole for the screw measures 7.5 cm

my version of the t300 shifter mod for the rs Ferrari rims printed my one with a 0.28 layer hight .

You also wont have to cut, glue or drill in any of the Original Parts so you can easily go back to the Original g27 Shifter if you want to sell it or just dont feel like using this Mod anymore. I put a lot of time into this Project and really...