Filament Feeder for XYZ DaVinci 10 Printer 3d models

A user observed that on a DaVinci 1.0A printer, the screw hole position deviates by five millimeters from its accurate spot, designed specifically for the 1.0 version. The piece was produced with a 20% density setting and a layer thickness of 0.2mm...

... chip. ...Simply remove the filament cartridge and plug in the Arduino for seamless connectivity. For a more detailed walkthrough, visit our project page at https://www.codemacs.com/coding/other/hacking-davinci-xyz-3d-printer-filament-chip.5168391.htm

Printer model: Davinci Pro 1.0 3-in-1 A small design enhancement allows for easy insertion of the 3D filament into its inlet. Filament inlet diameter is exactly 3 millimeters. To achieve precise results, provide a precision file to smooth out the...

I designed a straightforward filament guide for the XYZ Davinci Junior following my creation of a larger filament spool holder, which is also featured on this site. ...You're encouraged to experiment and modify it as you see fit; while its appearance...

Yes, there is a way to flash toose cartidges of spool from Davinci printers!!! this device is meant to hold the cables while you flash that chip with a computer assisted arduino to re-use the cartridges over and over. All you need is an arduino, a...

... 8. Test the printer with PLA filament to see if it moves easily back and forth. If not, check that the pneumatic connector is properly aligned. 9. ...Screw in the TPU print at a temperature of 220°C or higher (nfc settings suggest 210°C + 10°C).

I recreated this using these sensors in mind: https://www.amazon.com/dp/B07P72MYMJ/ref=cm_sw_em_r_mt_dp_U_XRL9EbF1E6E41 This sensor assembly is mounted directly into the original stepper holes, with the filament sensors securely attached to the...

I customzied this make for my small XYZ DaVinci Mini printer. Now it is easy to print, and it have the maximum size for the DaVinci. Like the original, have you to trim the main parts at teh inner back side a bit, that the revolver drum fits in.

Wade Extender for XYZ DaVinci Printer: Check out the original design at Thingiverse - http://www.thingiverse.com/thing:18379 This mod adds more room to your existing Wade extruder. ... I used a 16mm LME08 linear bearing for smooth motion and extra...

NOTE: This requires bdwalker1's E3D mount and the listed fasteners available here: https://www.thingiverse.com/thing:1328848/files Additionally, this requires 2 M3 nuts and 2 M3x10mm machine screws to attach the modular holder for the pen(s) NOTE: I...

Just an attachment to turn a Davinci Pro printer into a pen plotter. ... NOTE: This requires bdwalker1's E3D mount and the listed fasteners available here: https://www.thingiverse.com/thing:1328848/files Additionally, this requires 2 M3 nuts and 2...

... I designed it for a feed tube to pass through, but it turned out unnecessary. Print Settings Printer: XYZ DaVinci Pro 3-in-1 Rafts: No Supports: No Resolution: High Infill: 10% Notes: Sliced with Simplified 3D and printed in Transparent Yellow ABS

https://youtu.be/qE8cBWm1Nek More about design https://theveel.com/3d/horizontal-filament-feeder-for-printer-chamber/

More about design https://theveel.com/3d/horizontal-filament-feeder-for-printer-chamber/ Print instructionsCategory: 3D Printer Accessories Summary More about design https://theveel.com/3d/horizontal-filament-feeder-for-printer-chamber/

This is a very simple iPhone 4 / 4s mount designed specifically for the Davinci XYZ 10 3D Printer. The mount itself securely attaches to the top inside front of the printer, where you will find a piece of angled metal coming out from the frame. I...

for dual head. ...avoid wet atmosphere, put silica gel inside.https://github.com/atsukita1969/filament-spool-feeder

... ...On the left side of a DaVinci Pro 3-in-1, there are two small holes that you can attach this part to using M3 screws. These holes may be present in other DaVinci models. Print Settings Supports: No Infill: 25% Category: 3D Printer Accessories

... ...On the left side of a DaVinci Pro 3-in-1, there are two small holes that you can attach this part to using M3 screws. These holes may be present in other DaVinci models. Print Settings Supports: No Infill: 25% Category: 3D Printer Accessories

... ...On the left side of a DaVinci Pro 3-in-1, there are two small holes that you can attach this part to using M3 screws. These holes may be present in other DaVinci models. Print Settings Supports: No Infill: 25% Category: 3D Printer Accessories

@ChatToBrian addresses this issue in his video, where he discusses his external filament holder and the filament entry hole on the printer getting worn. As you can see from my photos, I'm experiencing this wear issue as well. Furthermore, when I...

... wire brush, and nozzle tip cleaner securely in place. ...On the left side of a DaVinci Pro 3-in-1 model, there are two small holes that you can use to attach this part with M3 screws easily. ...These holes may also be found on other DaVinci models.

Run guide tube from inside of the printer to the side with the spool and attach the end to the printer using a guide tube retainer (can be found here on Thingiverse) tangential to the bottom of the spool and as far towards the back of the printer as...

... using Tinkercad, a free online CAD software. ...You can edit it directly from the website at https://www.tinkercad.com/things/aC8XWP5x1fM. Check out the Green Filament Bracket that inspired this design at https://www.thingiverse.com/thing:1461527

for dual head. ...avoid wet atmosphere, put silica gel inside.

Get ready to take your printing game to the next level with our premium spool holder designed specifically for Davinci XYZ 1.0A enthusiasts! This top-of-the-line accessory is engineered to provide a seamless and hassle-free printing experience. Key...

Everything runs smoothly, but I dislike the printer's built-in filament guide because it pinches the filament when the top is opened too far and makes changing the spool a hassle. To solve this problem, I designed my own external filament guide,...

This is a customized version of the CR-10 Feeder's base plate, remixed by Mina_gerges to accommodate flexible filament. I incorporated a clip on one side to integrate seamlessly with Recreus' Pressure Regulator, accessible at...

I tweaked the Deluxe Spool-Holder from XYZ's DaVinci, printing out their version initially but soon found its arms didn't reach far enough to securely grip my 202mm filament container. ...I set about extending those arms, rectifying this glaring...

... this mount for my raspberry pi encased in a case with a ribbon-cable connected camera. ...It fits to the side of my XYZ DaVinci 1.0a printer, friction-fitting over the ribs on the side plastic. ...The camera mount is adjustable on the ball-mount.

This spool holder is designed specifically for the XYZ DaVinci 3D Printer, accommodating spools with an inside diameter of 32mm. The model targets big Octave ABS spools, which measure 160mm in diameter and 100mm wide. This premium spool holder...