Falk Coupling 3d models

Even without the use of LEDs, this version has a couple of other benefits. Printing two smaller pieces is less risky, in the event of a print failure. Also, getting even the small hex key in position to secure the side screws (see below) is easier...

I have included a couple of fun xenomorphs of mine, inspired by the movie. One of them works as a great stopper from rolling from the shelf. You can also check out my printable xeno set: https://www.thingiverse.com/thing:5702123 Updates: -...

Just make sure the linear bearings are in the correct holes to run on the rods as their are positions for four bearings. Shopping List:M3 bolts of various sizes (exact sizes aren't very important).M3 hex nuts2x threaded rods and nut pairs from...

The "Chain and rear belt mount" is made to work with the stock dragchain and have a couple cable management holes for those who want that. The back part serves as the belt mount since this system also swaps out two belts with one long so that the...

* Minor corrections to a couple of iPad Air 2 measurements. * Added support for swapping the camera/home button sides. * Added support for sloped sides on outer arcs. **UPDATE 08 Nov 2018 (version 11)** * Added support for iPad 6th Generation, iPad...

Print stuff: I used PLA on everything except the bottom tank ends, I used PETG with a couple extra top and bottom layers to make it watertight. I used pipe cement to attach it to the gutter. Everything else was just printed at whatever setting I...

If your printer can do magic or if you prefer using your slicer's support, say false here: CouplerSeatingSupport = true; // CouplerSeatingSupport = false; If your slicer is cleverer than I would expect, you may also say false here: side_support =...

Swap extruder for gearbox Align the threaded rods of the Z-axis, possibly using jaw couplings. 32bit Hardware https://www.thingiverse.com/thing:3629440 #3. Simplify levels# attach a 4th bearing to the Y-carriage...

A remix of http://www.thingiverse.com/thing:11978 to remove the top bar in the links and instead provide springy clips which can be easily removed and replaced to keep the cables in the chain, while still allowing them to be replaced without having...

# Notes for Micro SD card extension You may notice in a couple of photos, there's a Micro SD card ribbon cable extension going from the Pi to the side of the case. I've not uploaded the design for this, because the ribbon cable is very prone to any...

... Couple of tips 1. Set up a work area with a towel or something soft and large to work on, the screws disappear as soon as they are dropped. 2. Liquid tape works well in areas where adding heat shrink isn't an option or where weight is a concern. 3.

There is a front tray (Width: 215mm x Front-to-back: 45mm x Depth: 12mm) for odds & ends such as erasers, pencil stubs or other small artist's tools etc. There are a couple of configuration options here, with a larger base with a tray in front, a...

There are a couple of tricks I employ here to make this work: Slightly increase your extrusion multiplier, which will ensure that the there aren't gaps at sharp corners. (I increased my from 1.0 to 1.1.)</li> <li>Increase the overlap between...

Equipment Shot under the unfettered influence of breathtaking scenes captured using an accomplished tool crafted to serve perfection: the Magic Lantern coupled with the esteemed Canon EOS 600D. With its precision in providing artistic flair as...

Once together, you might have to squeeze the sliding piece in, and pull it back down a couple times to break it in. This is normal, and after doing this for a number of times, it will move as intended. Now, place a piece of VHB tape on the puck, and...

There are also a couple of versions of it. You can make the "original one" as a fishing boat, but you can also make a tug boat version that has a tow hook instead of the fish box behind the cabin. There is also another version of the roof with...

#10-32 x 1/2 in.1 small nut for the small thumb screw above.1 lamp cord1 bulb socket1 lamp harpOPTIONAL:You can paint/stain the wood to achieve the appearance you desire.I decided to use Danish oilAlso sprayed the thumb screws and nuts with rust...

##### Fasteners * T Nuts - I would recommend buying an assortment pack like https://www.amazon.com/gp/product/B07FPLZXTF/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 although you mainly need M3 sized parts (and the Ender 3 kit comes with a...

I ended up using #6x3/8in sheet metal screws, and a couple #6x1/2in for the side attachment. Narrow computer fan screws (with blunt ends and very coarse threads made for cutting their own threads in plastic) 1cm-long and 3mm diameter would be ideal...

Make sure to leave them on for a couple minutes and check if there is excessive heat buildup at the LEDs.Note:&nbsp;Some manufacturers of LED strips run them very close to their rated maximum, which makes them run rather hot. I noticed that my LEDs...

if you have the simulated power switch on when you turn the main power switch on, sometimes it just jumps straight into the idle hum, sometimes a couple of the lights turn green. either way the gun works as expected once you push a button.</p><p>If...

if you have the simulated power switch on when you turn the main power switch on, sometimes it just jumps straight into the idle hum, sometimes a couple of the lights turn green. either way the gun works as expected once you push a button. If you...

a couple of weeks, count the days) and do it again to get two new date-ranges- one of those will be the right count-of-days different from one of the first date-ranges, that pair is the one to accept. If there's still ambiguity then do it again. If...

These will keep the unit from sliding around, and also provide a couple of mm of clearance for aiflow to the grills on the bottom of the case.&nbsp;Additionally, there are holes under the feet that can be tapped for 3m screws for attaching...

Screw the screw in until it just hits the bottom of the eccentric slot, and then back off by a couple of turns. The end of the screw should not scrape the bottom of the slot during operation.</p></td></tr><tr><td>15. Press the little hook over the...

I backfilled a couple missing files. Note: This currently requires that the front of your Vertical mount be 50mm in front of the vertical profile supports for clearance at the top and bottom. There is a picture with a red arrow showing where this...

Adjust the left side gantry back screw as needed.Install the Left Gantry clamp.Loosen one of the grub screws on the Y-drive couple. This will allow the left and right pulleys to rotate independently. The grub screw will likely be quite tight.Connect...

However it still may be worth adding to existing to prove the operation first. Feed around 1m chain through cord wheel. Pull down existing blind cord to establish fully open position. Back off slightly and fit end stop in left cup. Use cord connector...

Extract the Chamber, using the magnet Lid knob to position the bottom lock in the center and the apply the push pin into the hole in the side, depressing the lock tab on the Chamber.The first few times you open the box the surfaces are still a bit...

The spring must move freely and press the lock nut away from the spindle nut. Now you can connect the T8x100 spindle to the coupling of your NEMA motor again. The spindle nut and the lock nut must be clamped into each other so far that the TR8...