Concave Dodecahedron 3d models

Leakage from this joint should be negligible over time.The reason for not integrating the inner "cap" into the backplate body is that the concave side needs to be on top (not an overhang) to be clean enough to mate to the o-ring. I could have flipped...

Hopefully you can fix by resizing in your slicer.The intent of the big circle is to keep the whole thing hanging vertically -- without it, the weight of the bar and towel pushes the whole thing against the wall.My bar had a slight concave curve in...

It can be short, long, or even concave, whichever is needed but most importantly, a rail that is easy to make. Or if only the pan motion feature is needed, it can easily be mounted on a tripod with its Quick-mounts that fit all standard cameras and...

You can find the X and Y version of this mod here: https://www.thingiverse.com/thing:4283647 To perform this modification, you'll need to purchase: * 2 - 7/16-14" x 36" Steel Threaded Rods - https://amzn.to/39d0SsW * 8 - 7/16-14" Nuts -...

The concave part should print upwards. Only the Endcap needs supports to the build plate to support the screw attachment point area. The MicroUSB cap snaps the micro USB board inside the Endcap before the extrusion goes in to hold it all together. Be...

Here are their approximate specs: Smaller Board: 90mm x 30mm, 40mm wheelbase, 18mm nose/tail with 25º kick, deck concave is 3mm x 30mm Larger Board: 98mm x 32mm, 50mm wheelbase, 18mm nose/tail with 25º kick, deck concave is 3mm x 36mm Bonus Content...

You can expand upon this lab to include determining whether convex or concave lenses can influence that threshold level as well. To experience circumference: Supply students with the car and some linear measurement devices. Talk about dimensions of...

The raised cup in the center is to catch the moisture that forms at the concave portion of the bottom of a typical Mason canning jar. Normally, this would drip back into the source jar. Print this in some safe plastic like PETG or PLA if you're...

The link has concaved scalloped edged to accommodate an optional locking clip which can be applied after the link is installed on the vehicle. It clips over the sides of the link and has two D-shaped "fingers" that poke into and fill the "ear holes"...

The raised cup in the center catches the moisture that forms at the concave portion of the bottom of a typical Mason canning jar. Normally this would drip back into the source jar. Print this in some safe plastic like PETG or PLA if you're worried...

If the fully assembled insert is slightly convex (when looking at the window from outside), you can try to increase it (something like 0.4-0.8 dgr), until the part becomes flat or slightly concave (which is acceptable as the window glass will be...

## Step 12 Carefully invert the outer gripper portion and plunge the blade of an Exacto knife straight down in the center of the concave recess until it barely reaches the end of the air channel. This is actually the valve as the silicone itself...

A raft helps with removal as well as adhesion. The hook MUST be printed with supports, lying down on its side, at a high detail setting. I recommend printing the concave 60mm spindle whorl at a high detail setting. It's little chunky otherwise.</p>...

This design will be fastened together using nuts and bolts thru the U channel aluminum extrusion) Battery (The Pint had room for only a 15s1p battery, mine will have room for a 15s3p and maybe even 16s3p, I am working for a 15s3p form so I can reuse...

So I made the outer (or convex) face one layerline thick and the inner (concave) another line thick. In vase mode the printer can lay the outer and inner lines in a spiral by continuosly extruding two lines per layer and going back and forth on each...

:-)All parts are already oriented correctly for printing and none require support material.You can flip it front-face-up if you want, if your print surface would leave unsightly blemishes on the print, for example, but it'll require support material...

So I made the outer (or convex) face one layerline thick and the inner (concave) another line thick. In vase mode the printer can lay the outer and inner lines in a spiral by continuosly extruding two lines per layer and going back and forth on each...

See photos, which show the printed part next to the original, for comparison.There are still concessions to expediency: I didn't bother to match the curves on the left and right side of the latch (they are straight on this model), and I also didn't...

The auger has been specially made to be concaved so as to hold the marble close to the shaft. The collector plate sits on top of the worm drive and is where the marbles are collected to be lifted up the auger. At the top of the lift is a special...

Topeak_Prepstand_concave_part.stlThis is the smaller part towards the main pivot point between the arm and the main vertical tube of the stand. Print with teeth facing upwards and supports underneath. I printed with 100% infill to get the piece as...

Finally I have included 2 more designs (BV2), they are the same as the reinforced design but have the concavity/convexity of the original design to fit the mudguard. In one model the top recess is flat and in the other one it is rounded. These...

Adapt the design by stenciling your eMail on the inward facing, concave outside of the belt holder. I always do that and found people are more honest than media tell us. You are, too, are you not? Adapt the design for your eye distance, it...

I have created a 3D printable part to replace the concave part of the swiveling adapter, so that it already provides initially a direct vertical view to the mobile phone, while keeping the possibility to adjust it further to your needs. This part...

- For really smooth curves and edges, go with .1mm layers, for some cool effects from the tiny concave changes in the flower petals, go up to .2 or even .3mm - maybe even try the prusaslicer auto layer height thing! Just have fun, and when you're...

A slight drag is OK, but if the wheel stops turning you may have to sand down the filament guides and/or drill out the filament paths (the concaved part may rub on the TPU wheel depending on printer tolerances, and 2mm drill works well to clean the...

The ability of individual focusing of the mirrors in a concave type assembly, in combination with the high precision of the orientation of the system allows a much greater distance of action compared to any other system. Additionally, the centers of...

I also added an additional beam for the camera cable to go through for better cable management and added a concave area on the right, as this would interfere with the BLTouch. I change the case to have thicker clips on the front part, as I printed...

The brace will help stabilize the frame and the added room gives you enough space to easily run a 330x330mm hot bed surface. For this mod, you will need to purchase: • 2 - 7/16-14" x 36" Steel Threaded Rods -...

Here are their approximate specs:Smaller Board:90mm x 30mm, 40mm wheelbase, 18mm nose/tail with 25º kick, deck concave is 3mm x 30mmLarger Board:98mm x 32mm, 50mm wheelbase, 18mm nose/tail with 25º kick, deck concave is 3mm x 36mmBonus ContentI've...

For larger printers (12.5” or larger panel), you may want to put it slightly off-center so avoid concave in the center build plate. 3. Print and wait for the results 4. For initial checking of results, you can stop the print at 3.5mm height (70...