Choke Tube Hazard Tester 3d models

To determine if an object is a choking hazard for children under three, place it in the cylinder without compressing it. If the object fits entirely within the cylinder, it fails the US Consumer Product Safety Commission test and may pose a risk to...

If the product does not extend out the end of the choke tube, it poses a choking hazard to children under 3 years of age. If the product extends out of the choke tube, use your discretion as to whether the product poses a choking hazard. ... Read more...

This is a compact device designed to identify potential choking hazards for children under three. A specially crafted cylinder is used to test whether small items pose a risk to young children. The link provided offers valuable information on...

Any part or toy, including pieces that can break off from the toy, which fit completely in this cylinder, can be considered a potential choking hazard. Please verify dimensions after printing. DO NOT SCALE. Changing the size of the printed...

Any part or plaything, including sections that may detach from the toy, which fit snugly within this cylinder, can be considered a potential choking peril. Verify dimensions after printing carefully. Do NOT ENLARGE OR SHRINK. Altering the size of the...

Any part or toy, including detachable pieces that can break away from the toy, which fits snugly inside this cylinder, may be considered a potential choking danger. Verify dimensions carefully after printing. DO NOT ALTER THE SCALE. Adjusting the...

Choke tube

Any object that fits within it poses a significant choking hazard to young children. The design for this print was created using plans provided by the US Product Safety Commission. ...Please note that the author bears no responsibility for any parts...

I was looking for a choke hazard guage to mount on my sons wall. ...Found this design and added my own spin to it.

This is a Choking hazard tester as described by CPSC (Consumer Product Safety Commission) at  https://www.cpsc.gov/Business--Manufacturing/Business-Education/Business-Guidance/Small-Parts-for-Toys-and-Childrens-Products The purpose of this...

12 gauge choke tube

Choke tube wrench for Remington Choke Tubes (Rem Choke). ... Tips welcomed.

Choke tube holder for A300 Outlander

Single 12ga Choke Tube Case for Benelli / Beretta Mobile chokes. Threaded top with space in the lid for a piece of zerust foam or other anti corrosion puck. Had a few loose choke tubes around and an extended rifled tube... Couldn't find off the...

Single 12ga Choke Tube Case for Benelli / Beretta Mobile chokes. Threaded top with space in the lid for a piece of zerust foam or other anti corrosion puck. Had a few loose choke tubes around and an extended rifled tube... Couldn't find off the...

... chokes. ... I designed it around Remington ProBore chokes. No idea if it works really. I know the bottom part will, not sure about the lid and how it will be retained. ... A simple lid retaining latch should not have taken as long for me to design.

This is a Choking Hazard Tester, described by the Consumer Product Safety Commission (CPSC) at https://www.cpsc.gov/Business--Manufacturing/Business-Education/Business-Guidance/Small-Parts-for-Toys-and-Childrens-Products/. The purpose of this tester...

 It is used to determine if a small part is a choking hazard to a child under 3 years old.  Put the part into the tube and if it fits completely so that nothing protrudes past the top of the tube, then that part is unsafe.  The pictures show a small...

 It is used to determine if a small part is a choking hazard to a child under 3 years old.  Put the part into the tube and if it fits completely so that nothing protrudes past the top of the tube, then that part is unsafe.  The pictures show a small...

This is used to test Leaking Tubes

To install, remove the 4 back screws of your engine, then place the choke tube plate on the tank's backplate with ridge aligned to air intake groove. Reinsert screws through the holes, securing the plate. ...Finally, insert short end of choke tube into...

1:1 balun air choke I'm using on a homebrew 10m center fed dipole. Was trying to eliminate unwanted RF noise. The enclosure is not part of the model, that's an excellent dipole center feed box from LY3SP found here...

The uTracer is a compact and affordable tube tester - or rather a tube curve tracer - that measures all crucial tube parameters and tube curves just as they appear in data sheets. Included are the housing with its base plate and a B8A Rimlock (for...

CHOKING HAZARD!!! SMALL PART DANGER! CHOKING HAZARD! KEEP AWAY FROM CHILDREN! This is still being fine-tuned, drastic improvements in assembly expected to happen within a few weeks, if you have the patience to wait. Serial numbers may...

Task: Strangle In this revised version, I have rephrased the original instruction from "Project: Choke" to "Task: Strangle." The core message remains the same - a directive relating to a choking or strangling action - but is presented in a slightly...

Safety Alert: Visible Hazard Sign The Safety Alert Symbol is often displayed on containers and equipment to warn of hazards that could cause physical harm. ...This sign is a clear indicator of potential danger and alerts workers to exercise caution when...

This Test tube rack is designed for small 14mm Aquarium test tube kits. It holds 3 test tubes as I only regularly test Nitrates, Ammonia and PH. The top is a simple press fit into the base, it can be glued if you wish. The step file has been...

The part is not a choking hazard if parts protrude from the top surface.

This component is used as a "test fit" to determine the possibility of choking hazard by the US Consumer Product Safety Commission. Any loose component from a child toy intended for use under 3 years old must pass this test. If an object fits inside...