Captian Jack sonic Blaster display stand 3d models

Here's a fresh take on OzzytheMozzy's Display Knife Stand, reimagined from the ground up. The curves of the surfaces and edges have been refined for a sleeker look. This updated design is more streamlined, with a shallower groove to hold the blade in...

I put together a quick and easy display stand for these hygrometers I have been using. All that is needed is an M3 50mm bolt and nut (as the hinge). ... As far as I can tell, the size of the hygrometer is pretty standard, but The ones I have are: ...

I did 5 minutes of research and decided I didn't like any of the display stands for pens, so I made my own. ...The pens I make end up being a tiny bit big but they just barely fit.(edit) I've remade the same thing but made the racks a bit thinner so...

... would complement each piece without drawing excessive attention away from their natural beauty. To achieve this, I drew inspiration from an acrylic stand I had previously used, but with some key improvements to balance aesthetics and functionality.

... screws to combine. Figure Display Stand, Measure just under 8" at 194mm with maximum figure stance of just under 5" at 124mm. Can accommodate a 60mm diameter x 8" thick puck light for lighting effects. ... Will require supports everywhere enabled.

Third iteration of the display stand arm. It's a more simplistic design that doesn't use screws/nuts at each joint. The tolerance between joints generate enough friction to hold up lightweight models. ... Custom bases can be made by dimensioning the...

... work just fine. Modified the stand I made for the CZ P10 series to fit the bigger glock mags and made the peg a little larger to make the pistol fit slightly more snug. This should still go on easy! ...If not let me know so I can adjust it :)

Display stand for Smith and Wesson M&P double stack series of pistols. Should fit the subcompact all the way to the full-size 5" models. ...*will not fit shield models* *DISCLAIMER* Do not have an M&P (unfortunately) to test this with, if you print...

This is a simple easy to print Display Stand for the Nintendo 2DS. If you are building a kit it was designed with x2 1/2" 10-32 machine screws and nuts. ... If you don't have a 3D Printer I can make it for you from my stores on eBay and etsy ...

This Keychain Display stand is great for modeling any item that may be a bit too fragile to carry every day. Seen here with a time turner from this listing: https://www.printables.com/model/503392-harry-potter-time-turner-print-in-place The Hoop fits...

I wanted something to display my old Gameboy Advance and the games I grew up playing, so I designed this stand. The only place it needs supports is the empty space directly under the Gameboy. I made it to hold the exact number of games that I own,...

This is a display stand for the original Game Boy, works with or without a battery cover. ... If you want to make a Kit you will need 2x 1/2" 10-32 machine screws and nuts If you don't have a 3D Printer I can make it for you from my stores on eBay...

This is a simple easy to print Display Stand for the Nintendo DSi. Won't fit the DSi XL If you are building a kit it was designed with x2 1/2" 10-32 machine screws and nuts. ... If you don't have a 3D Printer I can make it for you from my stores on...

Model Engine Display Stand for, O.S. Max 10 FSRO.S. Max 35 FPCox Babe BeeCox Babe bee (with tank)Kyosho GX-12 For the Cox engine there are two versions ( with or without a tank).And the Kyosho logo text was too smal for my printer so there is a "no...

I made this simple display stand for NES cartridges because the others I found here just didn't cut it. This one has a great angle, a slim design that fits perfectly, and keeps dust from getting on the connector/pins. ...To get the best results, I...

A Gameboy cartridge display stand for games with protection enclosure.You need to place the bottom face to your printing bed in your slicer (e.g. ..."Face on plate" in PrisaSlicer) because I used the top face as the base plate in FreeCAD.Note: The...

Slice with the settings you feel appropriate for the weight of the book you plan to display. The picture is done with zero top and bottom layers for the mesh effect. ...The pieces will slip together and stand but I recommend gluing them for better...

This is my rendition of a recent Oakley sunglass display stand. My version uses 6-32 machine screw hardware for the upper "hoops." I could have created this to completely snap together, but it would have consumed much more time. My total CAD...

A display stand in standard and compact versions is available. This stand is highly versatile and can be printed to any size required! It's ideal for displaying CDs, or large enough to showcase pictures, books, etc. Printing proceeds quickly! I use...

A display stand for 4 folding or small fixed-blade knives. Comes in two versions, one "hollow" (blue renders and photos) and one solid (red renders).</p> <h3>Print instructions</h3><p>At 100%, both versions come up 75 mm wide. ...Prints on its side...

... It comes with two larger side spots for short fixed blades, sharpening stones, lighters, or any other EDC items you would want to display. I cut a decorative curve into the top of each knife slot, which looks pretty rough at 0.3mm layer height.

So, I went about designing a stand that displays the cubes standing on a tip. I chose 5 cubes for the display taking into account the number that could actually fit as well as choosing an odd number to give a more pleasing symmetry. Forgiven my...

Car Jack for Crawler Scaler Trucks Cars.

... Stand, sidearm of the feared imperial Storm Trooper. ... All the other stands torqued over to the side since the magazine hangs over so I made one that supports the blaster properly. Want to buy an SE-14R prepainted and wired for lights and sound?

I recommend measuring the bottom of the glass with calipers and choosing a stand with a diameter slightly bigger.&nbsp;&nbsp;ConnectorsThe connectors connect each one of the individual glass stands together. The system is designed to have one row of...

The Hellboy PROP Gun model by Dan0nator (http://www.thingiverse.com/thing:71235) is so sweet it deserves a display stand. I included the stand with and without helper tabs - the tabs helps keep the print from lifting. The ammunition in the photos can...

I created this stand to display the print (also it it just tall enough to allow you to spin the model on it lol). The stand is barely visible (in the photo, the light blue one is on a stand, the other one is not), so you can probably print with...

This is a display stand tailored specifically for showcasing glass marbles in a stable and visually appealing manner. It features a spherical cutout precisely designed to accommodate marbles measuring 1.5 inches (38mm) in diameter, although the...

El stand funciona mejor en comics gruesos, pero también puede servir en grapas, para este caso recomiendo usar un papel grueso en la parte de atrás para dar soporte al comic. Tambien recomiendo dejar los comics en sus bolsas protectoras. Dejo el...

Put your collectible coins on display.