Bondtech Extruder 3d models

Printed on a ReprapGuru prusa i3 with a direct drive extruder and PLA filament. Models were sliced using Cura. This replacement head strap uses the original earcups, axles, screws, plastic screw plates, and head strap padding of the headphones. Be...

I also loosened the tension on the extruder gears to where it barely closed onto the TPU. The filament stripped the first two times I tried to print the parts. When I finally printed the parts correctly, the TPU parts had a lot of stringing, but with...

I find slight variations in line quality acceptable; extruded plastic is more forgiving than a pen or marker when it comes to print surface/levelness. You might need an M3x6 screw, depending on your writing tool of choice. The photo of the bed...

If you are using the standard plastic stock extruder head, you will need to snip off the cable shroud clips adjacent to the bowden tube nozzle to clear the new cable tie retention detail. ... Print Settings Prototypes printed with Tronxy Orange PETG ...

I also include a 3MF file with the mount I used to attach the Bear BGM extruder.Optional Parts: This file has a few optional parts that you might be interested in. Power Switch Mount can be used to hold two switches for Power and Lights. The file can...

If the 12 is aligned Mount the adapter plate (cuts an M3 thread into the small holes at the bottom) and the extruder unit. Screw the bracket to the 7-way rail. Push both units on top of each other and check for fit. Aligns the 7s fine. The whole...

Voron V0.1 Tophat Spacer with HingesMakes the tophat higher, stiffer and adds a hinge.Therefore its a lot easier to open the top and adds 20mm more space in the top for cable routing and higher Extruders.I added now also a Version which is split for...

These "Cable Danglers" mount on a horizontal 2020 extruded bar and are very configurable for hanging cables toward the centers of where they might need to travel. The suspension is flexible, using "music wire" (sometimes also called "piano wire" --...

The sketch was then extruded to a basic shape, a copy was scaled for the fin tip, both were aligned, and the fin was created by lofting through an intermediate profile. A straight swept fin can be done by lofting from the base to tip profiles. The...

------------------------------------------------------------------------------------------------------------------------ ## Before You Print This bookmark *does not* require a multi-material extruder. Instead, each STL is printed as a different...

2018: After printing a full set of the files, I realized that the outer core was too long, when I extruded it in Fusion360 I didn't take into account the offset I gave it for the bearing spacing. It's been fixed now and the files have been updated. I...

A fresh remix of the Dagoma dual extruder back face drawing inspiration from [Face avant renforcé Discoeasy200 by ragnaroque](https://www.thingiverse.com/thing:2077102) and a Y-belt tensioner from [Faces AV&AR améliorées pour Dagoma DiscoEasy &...

Be cautious not to under-extrude, as water could leak through the printed seal itself. A smooth bed, such as glass, will help achieve a good seal. Assembly: Orient hinges and latches according to cross-section images, ensuring hole alignment on the...

After I was allowed to use the printer, I started the first print and discovered that the extruder kept making this "clicking" sound, which led to my prints failing. After two weeks of troubleshooting I decided to completely disassemble and...

0.2 layer height ;) --- Part cooling duct - no infill, 3 walls, 3 top / bottom layers --- Hotend fan shroud - no infill, 3 walls, 3 top / bottom layers --- Part cooling fan bracket, 25% infil (grid), 4 walls, 3 top / bottom layers --- Fan Cover,...

I personally used 1.524mm(.06") cast acrylic, but extruded is easier to work with. The slots are about 3- 3.5mm wide, depending on how you slice/print it Instructions are nearly the same as the original authors, except the plexi for the sides will...

Typically, runout sensors are positioned much closer to the extruder for minimal filament waste. However, I converted my CR-10 to be direct drive and the position of the sensor makes the most sense for my setup. As an added benefit for its position,...

It can also work with the bowden fittings on most 3D printer models, both on the extruder and the hotend side. These fittings often get stuck on my printers, but with this tool they can easily be removed. This is my first time using Blender for...

This is a completely new version of my original design (here: https://www.printables.com/model/145632-dslr-rig) without the cage and with fewer parts. Redesigned in SOLIDWORKS for higher precision.UPDATE (19/04/2023):Uploaded .STEP files (exported...

However, I have now included another lid, This time the Text and Pentangle are Extruded so you can add another colour filament, Maybe a glowing one! See image Galaxy Silver and Black.If you didn’t want to use the box as a ‘Jack-in-the-box’ then the...

Some nut holes are closed with 0.2mm thick extrude to improve print quality, use a small drill or a file to open them after printing. The shifter paddle in real-world pictures is different from the one that is available for download. Update 1: Added...

If you want, you can make the PTFE tube long enough to reach the extruder.When you've finished printing, cut the filament off ready for its next use, with about an inch sticking out of the end of the PTFE tube, then just pop it back into the...

For all those who want to print in multiple colors, regardless of whether they use a multiple-color or solo printer, the heights for the filament/extruder change (color change) follow. I printed all parts with 0.4 Nozzel and layer height 0.3 (except...

(except for that of the X axis) - Y cable for the direct drive extruder - E cable for the Z axis motor - Z cable for the Y axis motor With regard to the impressions of the parts, a minimum infill of 30 for the rigidity of the parts subjected to...

Provided Factory files are tuned for Direct Drive Cartesian printers with geared extruders and auto-leveling. Bowden equipped printers have typically more lag due to the added friction inside the Bowden tube, and you need to reduce retraction with...

 It will be like a custom piece of art that filters the air in any space you need!!! I may add some storage or wall mounts to the design at a later date.  SO NOW TO THE FUN PART!!PARTS: ACTIVED CARBON PREFILTER Amazon.com: Universal Cut to Fit Carbon...

Anything from the filament spool to the MMU and from the MMU to the extruder head. &nbsp;I needed two orders of the following:<ol><li><a...

Designs on thinigverse: These are nice but dual extruded, most of us can't do that trick. https://www.thingiverse.com/thing:12285 https://www.thingiverse.com/thing:2532326 I really like the idea of the cube, but a sharpie was used Maybe I...

In vase mode the printer can lay the outer and inner lines in a spiral by continuosly extruding two lines per layer and going back and forth on each layer. Further I think this could be a Method to print masks for cosplayers, without a need for...

It allows the filament, and the extruder cables, to go through and still keep the entire setup closed. All the parts: Doors: 8x Hinge, Hingebracket &amp; Pin; 2 for each door 4x 2mm spacers; 2 for each front door (3mm spacer for tight fit) 4x 6mm...