Adapter to use any SATA drive in Seagate FreeAgent GoFlex 3d models

Introducing the Seagate FreeAgent GoFlex Desk Desktop Adapter, which utilizes standard SATA connectors to easily accommodate any drive. However, without the costly mounting housing, drives may fall out; hence, I designed a solution that enables safe...

The Seagate GoFlex drives that have a small sata dongle bombs out when the dongle goes. ...The solution is to crack open the chassis and stick the drive in a standard enclosure.

Now that you know how it's done, grab an RCT tray from any number of online retailers, which conveniently includes a sliding mount for your new friend Seagate GoFlex - now all high and proud at 15mm high (because you knew better than to choose...

I printed it in PLA but may deform in long term under heat. ...So may better choose PETG.

The Bottom piece attaches to the SATA connector of your hard drive. There are two Bottom options: tight for slim drives and printable without a Top, while normal is suitable for all drives and enables sliding in and out. This mounting solution offers...

As of yet, this has not been put to the test.

This adapter serves as the solution for attaching any laptop-sized 2.5-inch hard disk drive to your Seagate GoFlex docking station. The design accommodates the weight of the drive and relieves stress on the connectors. With its adaptable height...

Housing for the USB to SATA controller (100DB02 ?) PCB found in Seagate FreeAgent external HDD. This housing allows to attach a 2.5" drive, in my case an SSD, to the controller while taking up less space overall. I made this so that I could have an...

Was trying to find a model for defunct goflex enclosures and as I could not find any I had to design it in fusion360. All mounting holes measured and perfectly aligned to fit seagate docks. Also included adapter for goflex docks so can use an...

Unfortunately, my PC's tray-less slide-in dock doesn't play well with 2.5" drives, so I needed an adapter to hold the drive in place while plugging it in. I browsed through Thingiverse and found a design for a 7mm hard drive adapter, but it wasn't...

... of leaving it to catch dust or throwing it away, i make a case for it. - good for Seagate Expansion Portable (STEA4000400) - two little screws, M2.5 5mm - hot glue as filler in between the board and case if it is a bit too loose for your taste

Recently i bought a Seagate Goflex Net but the original Seagate disks seems to be to expensive. So i put in a normal cheap S-ATA 2.5" disk. They fit in but very wobbly. OpenSCAD and Thing-O-Matic to the rescue! ...:-)</p> Category: Other

I purchased a Seagate Goflex Net recently, however, the cost of original Seagate disks was too high for me. To save money, I inserted an affordable S-ATA 2.5" disk. Although it fit, the disk wobbled excessively. Fortunately, OpenSCAD and...

... a 3.5 inch slot. ...It is especially useful if used with IDE to SATA adapters as in the OG XBOX and some old-ish computers. ...If you open the model and it looks really small, scale it up to the following measurements: W: 101.3mm, H: 15.35mm L:121.5mm.

This is a tool free way for you to use SSD's in your retro computing project with popular SATA to IDE adapter boards.The problem with these is that they don't usually mount to anything, and flap around in the breeze. This adds some security by...

3.5" to 2.5" adapter for PC drives. ...May not work for certain configurations. Designed to adapt drive sleds from 3.5 to 2.5 for facilitating an SSD upgrade on an older machine.

I haven't printed this part yet, but I'm confident that it will work as designed according to the 2.5 drive spec, including the position of the SATA connector relative to the mounting points in the long direction. In the lateral direction, the...

To secure the device, you'll need to choose from three available screw sizes: 8mm, 6mm, or 3mm. ...Simply slice a kitchen sponge to fit snugly within the rotary adapter, then attach it securely with the corresponding nut and bolt.

This adapter bracket allows you to accurately position a 2.5" SATA drive in a 3.5" hard drive cradle so the SATA connector fits perfectly into the backplane slot.\nThe model is engineered for a precise fit with my Kingston SSD, making comparisons...

The back is modified to accept a Vantec CB-ST00U3 SATA to USB adapter - similar to this from Amazon: https://www.amazon.com/gp/product/B07452Z3KH?ref=ppx_pt2_dt_b_prod_image No supports required. ... I'm using Hatchbox PLA and didn't need to adjust the...

My adapters measure approximately 50mm x 80mm, so I designed this adapter to prevent those nasty smoke-generating accidents that Murphy seems to take pleasure in causing. Printed in ABS, but any material should do, the screw holes are slightly...

Case designed specifically for 2.5-inch hard drives, paired with a reliable SATA-to-USB adapter; assemble using ten M3 bolts securely fastened together.

Greetings, dear friends. ...I developed this project for your convenience. Link to the adapter: https://a.aliexpress.com/_ALSqF0 If this project helped you, please like it. ...Thanks!

... should be maximum 47mm wide x 11.5mm high in order to fit inside this. Your 2.5" drive needs to be 7mm high or slimmer in order to fit.Printing notesIf you print standing up like the STL you shouldn't need any supports (but a brim could be useful).

... (priced under $4) Chinese adapters available on eBay and Amazon. Building upon a foundation originally designed for Western Digital drives, this new iteration has made some compromises in terms of mounting rigidity to achieve a more universal fit.

Case for SATA M2 (NGFF) SSD to USB Adapter Card. Some SSD get quite hot so i use the version with air vents. But it´s your choise and you can combine. There are multiple adapter card versions on the market. Can´t say if yours will fit. The one i...

... Fusion 360 file so you can remix it. It would be nice to have screws or an inset groove for the sides to sit into. I am using this USB adapter, Apricorn SATA to USB Adapter, which might fit others of the same shape like Benfei SATA to USB Cable.

I bought one of these (https://www.newegg.com/p/2WG-00AD-00015?Item=9SIA86V8VX7791) recently to use in a custom NAS enclosure. ...The connectors were designed using the official SATA 3.0 specification...

The BEETHEFIRST printer is now compatible with BQ's 300g filament spools thanks to a clever spool adapter that makes it easy to switch between different sizes and types of filament.

This is a simple lightweight tray adapter to be able to place a 2.5 in hdd/ssd in i a bay for a 3.5 in drive. ... It is made to be light and fast to print, taking strength from the drive that is in it.