93 miata dashboard 3d models
12582 3d models found related to 93 miata dashboard.
thingiverse
Remixed a Miata file to hold the aftermarket key fob for my NA miata. I used a [momentary tactile switch](https://www.amazon.com/QTEATAK-Momentary-Tactile-Button-Switch/dp/B07VSNN9S2/ref=sr_1_4?dchild=1&keywords=tactile+switch&qid=1633793354&sr=8-4)...
thingiverse
... Installation : 1. Pop in the spacer to the 3D printed part and screw in the M6 bolt 2. Pop out the tow hook cover on the miata (don't lose it, keep it) 3. Screw in the 3D printed part and tighten using a 24mm socket / wrench 4. And done. ...
thingiverse
This was small enough to self tap onto the stud of the Miata shifter without much trouble, but still hold well when trying to pull it off. I printed my model as a test to see if I'd like the short Momo Anatomico shifter, so I only used 15%...
thingiverse
Cap/lid for cupholders in Mazda Miata. Dimensions initially taken from customer via tape measure; minimal feedback on fitment. Your experience may vary, and sanding may be required to fit. **FILE MAY HAVE METRIC/ENGLISH UNIT CONFLICT. ...SCALE TO...
thingiverse
Here is my trunk lock delete for my 1999 NB Miata. I printed one out and made some adjustments to the file afterwards, so let me know if it works. The tapped holes on the mount are M6 x 1.0. ...The knob uses a 3/16" roll pin to keep it in place.
thingiverse
Miata windshield washer funnel. Slips over the bottle / tank to make refilling easier. Print in 2 parts to avoid supports. I included a file for each part and a file with both parts. ... I used superglue gel to bond the parts.
thingiverse
Ducting installed to swap fog lights on my NB2 Miata, featuring an outlet that takes a 2.5-inch flexible hose. On the inlet side, there's a ridge designed specifically to accommodate a metal mesh screen, which helps keep debris out by melting or...
thingiverse
If you own a NA miata you know the cup struggle after you get a large or small drink from anywhere while driving a manual so I fixed it. ...Use anything with good heat resistance to print with don't use PTG.
thingiverse
Here are the details on this Fuelrail spacer designed specifically for your 2001 Mazda MX-5 Miata with its 1.6-liter engine. ...It's essential to verify whether it will be compatible with NA (non-turbocharged) or 1.8-liter models before making a...
thingiverse
a single cup holder for Miata 89-05 diameter is at 72mm you may try to print it to a more heat resistant filament (ABS??). I printed it in PLA, it may deform due to heat. ... you may need to sand down the "hook" part.
thingiverse
Hopefully this will help someone out. ...I broke mine and didn't see one on here already. This is for my NA Miata but I'm sure it could work with NB as well. I printed this so the backside is on the bed. ...That way the part you see is much cleaner.
thingiverse
......This cap was originally intended for an NC model MX-5 Miata, but its design makes it likely to fit other vehicles as well. ...The stem is carefully crafted to be just the right size, requiring a gentle twist while inserting to ensure correct seating.
thingiverse
another miata cupholder that is placed on the passenger side footwell (replaces the bolt cover at the side for the tombstone).place a magnet on the dimples for it to be stowed away. ...use ABS or PET-G to avoid warping.
thingiverse
I'm working on a custom vanity plate design for my Miata that's based on the dimensions of aluminum. ...I've only done some calculations so far and haven't actually printed it out, but I think it could be really cool for car shows and I'd like to...