8bitdo holder 3d models

this is a dummy model

remixed for wall

Simple SN30 Pro charging stand made for the following magnetic USB-C cable (but I guess it should be compatible with some other brands as well) : https://www.amazon.fr/gp/product/B09CD3LHJZ/ The assembly should be a tight fit, but if it is too...

Remixed this controller stand to hold two SN30 Pro/Pro+ controllers. Also made a "short" version that sits flat on the ground, for the regular SN30 without the handle grips. ...Prints without supports if you rotate it to the side.

I changed the handle to get a better grip and a keychain in both sides I changed the clip to be more resistence and stronger so it dont break At the moment it has a "player_1" writen in the back, but i will change it in the furure At all, i...

I designed this custom case to safeguard the analog sticks on my trusty SN30Pro controller, as I'm always carrying it in my bag and worry about accidentally breaking them whenever I toss other items inside. To ensure secure storage, the cover clips...

I was determined to find a 3D printed phone mount specifically designed for the SNES30Pro. ...However, I couldn't locate one that met my requirements, so I decided to take matters into my own hands and create my own custom solution using a GoPro mount...

<p>I made this cover to protect the analog sticks on the SN30Pro 'cause I bring it with me everywhere in my bag and when I put something in I'm afraid of breaking them.<br/> The cover clips to the little holes in the controller for the original...

The original Modular system works great for the SN30 controllers, but on the pro models, the nubs for the analog sticks cause it to fall off easily. ...This just cuts out a couple circles so it can stay on the dock and fit a little nicer.

In my experience the 8Bitdo Controller is a great device, but the original Cellphone Holder has a terrible low viewing/holding angle, thats why i created that small thing. The adaptor is adding 22.5° to the holders angel and is compatible to all...

I had an issue with the original (that I remixed this from) fitting on the 8bitdo arcade stick. The mounting holes were a little too small, so I opened them up a bit. In the pic I have, I actually only printed it at 50% height as a test print, but...

The phone holder is now fully inserted, and fixed non-critical defects.

Using the base clip of https://www.thingiverse.com/thing:4794751, but removing the ball as I do not have this type of phone holder. Instead, adding a section from https://www.thingiverse.com/thing:1393617 and also printing rest of phone clamp from...

Wanted to get a little bit of ergo grip in there, this feels pretty nice, but could better if I was an engineer. First attempt, I may try again after extra play. ...But for now, it’s time to play Zelda!

To be printed with resin.

This remix from pixelauthor's SN30Pro+ Trigger plate.pixelauthor's version has a profile that allows the same trigger plate to be instaled on both left and right R2 button. However the one downside is the trigger plate profile does not match the...

Customized version of https://www.thingiverse.com/thing:5251017 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5251017

The Xbox version of the SN30 pro has the dimples opposite the sticks *just* slightly narrower than the standard SN30 Pro so the cover won't click in. ... I just moved the bumps on the cover and now it works perfectly.

Better grip for your thumb

I liked the original idea but those dimensions don't quite fit my phone and gamepad is sitting loose. Redesigned it from scratch in OpenSCAD to be parametrized for any phone size (tested minimum width is 75mm, any sane depth works fine). I have also...

A simple mount for playing your Switch / Switch Lite with your Arcade Stick :-) It works surprisingly well - both on a table/desk or on your lap. It is prevented from moving side-side by a hole that fits over one of the nobbles of the drawer for...

This model is coming soon to ALPHA testers in Discord.

I've created a custom remix of Jhonfa's popular NES30 Pro clip, tailored specifically for my Nexus device.

Remix from two awesome things, just get everything done on Tinkercad on 5 mins

Customized version of https://www.thingiverse.com/thing:5251017 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5251017

This version was remixed to fit a wired version of SN30 Pro.Infill anywhere between 40% to 100%, but I highly recommend using at least 4 to 6 perimeters for better flexibility "filament proprieties may make this setting vary".The clip that goes...

This is a replacement battery cover for the SN30 Pro+. It might also fit the SN30 Pro, but I don't have one, so I can't test it. This is the first model I made in Fusion 360! ...It's not perfect, but I'm proud of it.

I still can't figure out why the previewer isn't showing this STL file, but fortunately, it's slicing and printing just fine. ...To give you a better idea of what it looks like, I've uploaded a screenshot for your reference.