69 ltd 3d models

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

I had read on the forum that several people have had problems printing with this filament (clicking extruder), but that these problems could be avoided by printing at 230C and 69% of the speed. So I printed all puzzle pieces with these settings (I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes height = 15 shape =...

&nbsp;This lookup table may be useful:&nbsp;&nbsp;Absolute 0.6 mm Stem SizeRelativeTierFontptmmBlender SizeEM ScaleSOsifont23.688.3614.0551.0000Overpass16.385.787.2400.6916AVarela...

That's around 43€ to 69€ for chassis parts and 70€ for electronics! Or maybe you can take most of parts from other RC projects you don't actually attend... As you can see, this chassis is initially planned for building an On-road car, that could...

 This is exactly how mine is made and it works well, HOWEVER, if I did this again, I’d make the Front/Back and Top panels .25” wider to give a little more clearance, so I’d recommend 13.94” instead of 13.69” wide for the Front/Back and 13.32" instead...

If necessary, sand the holes and the bolt with fine sandpaper.Mount the hands as shown in the pictures.&nbsp;Step 4: Set Up Clock - Insert CubesAfter you have printed the fileClock_No_01-12.stlyou can place the clock in the stand and insert the 12...

Other standard settings will be fine, like infill of 20%, layer height of .2mm, 2 perimeters.&nbsp;At the end, turn the rings a few times to make them spin better.&nbsp;Ring size conversion table:Ring inner diameter in mmUSACanadaUnited...

There are also useful coat hangers and finger toys.Print instructionsYou can print it without any support, and it prints very fast.Standard settings will be fine, like infill of 20%, layer height of .2mm, 2 perimeters.After printing, turn the ring a...

You can see the support in green in the picture below.The ring still prints very fast, in 30mins.Other standard settings will be fine, like infill of 20%, layer height of .2mm, 2 perimeters.After printing, remove the support material and turn the...

In case your ring does not stick well during print, try the original fidget ring instead.After printing, turn the ring a few times to make it spin better.&nbsp;Ring size conversion table:Ring inner diameter in mmUSACanadaUnited...

This can be done with a breadboard to avoid soldering; using the perf board.Here is the Arduino...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 mirror = Yes shape =...

There are also useful coat hangers and finger toys.Print instructionsYou can print it without any support, and it prints very fast.Standard settings will be fine, like infill of 20%, layer height of .2mm, 2 perimeters.After printing, turn the ring a...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 30 mirror = No shape =...

The 3D printing model's chosen scale is 1/60 for the FFF/FDM version and 1/100 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 54 parts;- A printed model is 303 mm tall, 153 mm wide, 185 mm deep;- Made...

The model’s chosen scale is 1/8 for the FDM version and 1/16 for the DLP/SLA/SLS version.FFF/FDM version dimensions:A printed model is 248 mm tall, 137 mm wide, 316 mm deep;DLP/SLA/SLA Eco/SLS version dimensions:A printed model is 124 mm tall, 69 mm...

The model’s chosen scale is 1/8 for the FDM version and 1/16 for the DLP/SLA/SLS version.FFF/FDM version dimensions:A printed model is 298 mm tall, 472 mm wide, 479 mm deep - with platform244 mm tall, 144 mm wide, 278 mm deep - without...

There are also useful coat hangers and finger toys.Print instructionsYou can print it without any support, and it prints very fast.Standard settings will be fine, like infill of 20%, layer height of .2mm, 2 perimeters.After printing, turn the ring a...

The 3D printing model's chosen scale is 1/60 for the FFF/FDM version and 1/100 for the DLP/SLA/SLS version.FFF/FDM 2.0 version features:- Contains 71 parts;- A printed model stands 210 mm tall, 165 mm wide, 118 mm deep;- The assembly kit includes a...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...